background image

   Part # 4532285 Rev 4 (4/29/14) 

 

© 2013 Garland Commercial Ranges Limited 

     

 

 

 

 

Models: 

SH DU IN 7000   (2x3500 / 7kW) 

   SH DU IN 10000 (2x5000 / 10kW) 

 

                                  

 

 

INSTALLATION AND 

OPERATION MANUAL 

GARLAND INDUCTION 

BUILT-IN LINE 

DUAL-ZONE COOKERS 

with RTCSmp TECHNOLOGY 

R

eal-time 

T

emperature 

C

ontrol 

S

ystem 

m

ulti-

p

oint sensing

 

 

PLEASE READ ALL SECTIONS OF THIS MANUAL AND 
RETAIN FOR FUTURE REFERENCE.

 

THIS PRODUCT HAS BEEN CERTIFIED AS 
COMMERCIAL COOKING EQUIPMENT AND MUST BE 
INSTALLED BY PROFESSIONAL PERSONNEL AS 
SPECIFIED 

INSTALLATION

 AND ELECTRICAL CONNECTION 

MUST COMPLY WITH CURRENT CODES IN YOUR 
REGIION: 
IN CANADA – THE CANADIAN ELECTRICAL CODE 
PART 1 AND / OR LOCAL CODES. 
IN USA – THE NATIONAL ELECTRICAL CODE ANSI / 
NFPA – CURRENT EDITION. 

FOR YOUR SAFETY

 

DO NOT STORE OR USE GASOLINE OR OTHER 
FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF 
THIS OR ANY OTHER APPLIANCE

 

CE models

 comply with the latest European 

Norms: 
EN 60335-1, EN 60335-2-36, EN 62233 (EMC/EMV) 

North American models

: ETL listed in compliance 

with UL 197, CSA C22.2 No.109, NSF-4 
Complies with FCC part 18, ICES-001

 

WARNING

 

IMPROPER INSTALLATION, ADJUSTMENT, 
ALTERATION, SERVICE OR MAINTENANCE CAN 
CAUSE PROPERTY DAMAGE, INJURY, OR DEATH. 
READ THE INSTALLATION, OPERATING AND 
MAINTENANCE INSTRUCTIONS THOROUGHLY 
BEFORE INSTALLING OR SERVICING THIS 
EQUIPMENT

 

Users are cautioned that maintenance and repairs must be performed by a Garland authorized service agent using only 
genuine Garland replacement parts. Garland will have no obligation with respect to any product that has been improperly 
installed, adjusted, operated or not maintained in accordance with national and local codes and/or installation instructions 
provided with the product or any product that has its serial number defaced, obliterated or removed, and/or which has been 
modified or repaired using unauthorized parts or by unauthorized service agents. For a list of authorized service agents 
and/or genuine replacement parts, please visit our website at 

www.garland-group.com (USA and Canadian customers) or 

www.manitowocfoodservice.com  (international customers).

 The information contained herein, including design and part 

specifications, may be superseded and is subject to change without notice. 

   

 

 
 

Visit our 

Video Gallery

 at 

www.Garland-Group.com 

 

Summary of Contents for SH DU IN 7000





























Reviews: