Inner duct
Outer duct
Roller catch
Slit
Hook
Hook
Ceiling
Inner duct
Inner frame
1
1
2
2
3
Inner duct
Inner frame
Ceiling
3-9/16"
(90)
3-9/16"
(90)
1-9/16"(40)
5-7/8"
(150)
8-11/16"
(220)
4-
∅
9/16"(
∅
14)
∅
1-3/16"
(
∅
30)
Beam
Front
Stringpiece
11"(280)
14-3/16"(360)
3-9/16"
(90)
3-9/16"
(90)
6-15/16"( 176)
11-13/16"(300)
46-7/8"(1190) MAX Height
13"(330)
23-5/8"(600)
33"(837.5) MIN Height
3-1/8"(80)
14-3/16"(360)
16-5/8"(422)
15-3/4"(400)
16-1/8"(409)
16-7/8"(428)
19-3/16"(487.4)
13-7/8"(352.5)
5-7/8" (150)
30"(762) MAX Duct Height
Stroke
Duct Cover
(Outer)
Duct Cover (Inner)
7" (177.5)
1" (25)
36"(913)
24"(610)
18"(457)
1" (26)
Roof cap
7" round duct
(For vertical discharge)
Range hood
Lamp Switch
High Switch
Medium Switch
Low Switch
OFF Switch
Pilot Lamp
Control Switches
Lamp
(Not supplied)
Fan
Inner Duct
Inner Duct
Inner Frame
Outer Frame
Hanging
Bracket
Outer Duct
Outer Duct
Filter
Rectifier Baffle Panel
INSTALLATION MANUAL
Model: ECP-360
1U03 1881
Before installation and operation, read these instructions carefully
and use this product only in the manner described by the
manufacturer in the operation manual.
The instruction shown below are used to alert you to potential
personal injury and property damage hazards.
There are three hazard classifications based on potentially
dangerous situations.
Obey all safety instructions that show these symbols to avoid
possible injury, death and property damage.
SAFETY INSTRUCTIONS
WARNING:
WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION:
CAUTION indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
Screw
Inner frame
Outer frame
5
_
(1)
5
(1) Pull out the inner frame after removing 4 screws fastening to the
outer frame.
Note:
Keep the screws for reusing later.
(2) Fix the inner frame to the ceiling using
8 wood screws supplied after aligning
its holes with the threaded rods.
NOTE
: The safety instructions are explained with the following
pictographic symbols.
means forcible execution. It indicates actions, if
any, that must be done.
WARNING
1. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b) Before servicing or cleaning the unit, switch power
off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
CAUTION
INSTALLATION
1. Preparation
3. Connecting Power Supply Wires
1
Remove the nut from the conduit
connector at the end of power
wiring.
2
Remove two screws fixing the wire cover and detach it.
5. Assembly and Check
2
Two 50 W halogen light bulbs (not supplied)
can be mounted in this range hood.
Prior to function check, install light bulbs
(PAR20 bulb, in the base diameter 26 mm:
medium base), rated 120 V - 50 W or below.
Turn the lamps clockwise
to install them.
Range Hood
3. Read specification label on this product for further
information and requirements.
2. To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside. Do not vent exhaust
air into spaces within walls, ceilings or into attics,
crawl spaces or garages.
6. Fasten the filter and other parts securely. Incorrect
attachment may result in personal injury or
property damage.
4. Use only for the purpose of kitchen ventilation.
1. For general ventilating use only. Do not use to
exhaust hazardous or explosive material and
vapors.
5. Do not install this range hood in the bathroom or
in other wet rooms since electrical shock and
damage may result.
2. To reduce the risk of fire or electric shock, do not
use this product with any solid-state speed control
device.
b) Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and The American Society
for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.
c) When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
d) Ducted fan must always be vented to outdoors.
1
This range hood is designed to
install using anchor bolts as
illustrated and discharge upward.
For vertical discharge, run duct
work between the hood location
and roof cap location.
To get the best result, use a
minimum number of transitions
and elbows. Be sure to attach a
roof cap to avoid rain from
entering into the exhaust duct.
2
Referring to the figure below, make an opening on the ceiling and
reinforce around the opening with some beams. Then, make 5 holes
as shown in the figure.
• Ensure that the metal duct does not touch other metal housing materials,
otherwise fire or electric shock could result.
• Install the range hood unit using anchor bolts durable
enough to support its weight (withstand load: more than
441lbs. (200kg)/pc). Otherwise, it may be detached and
fall down.
6. Explanation to the End User
(1) Referring to the Operation Manual, explain the operation of this range
hood to the end user.
(2) The Installation Manual and Operation Manual should be given to the
end user.
Assembly
1
Attach the filters and rectifier baffle panel referring to the steps
described in “2. Range Hood Mounting”.
Check
1
Turn on the power to the range hood.
2
Make sure that the switches and light operate correctly.
Refer to page 4 of the Operation Manual.
3
Make sure that the range hood functions properly and it has no
abnormal noises and/or vibration.
• Electrical wiring should be done by a qualified person(s) in accordance
with all applicable codes and standards, including fire-rated construction.
An unqualified person doing the work could result in fire, electric shock
or injury.
• This range hood uses 120V AC. Do not connect to other voltage since
fire, electric shock or damage could result.
Be sure to switch OFF the power
at service panel before wiring.
3
Connect the conduit through the connecting hole of the body using the
nut previously removed.
4
Connect wires tightly and
securely using wire
connectors (not supplied).
Connect the electrical wires
as follows:
5
Replace the wire cover with the
screws removed previously.
Make sure that all wires are
connected properly and
enclosed inside of the wiring
compartment.
CAUTION:
CAUTION used without the safety
alert symbol indicates a potentially
hazardous situation which, if not
avoided, may result in property
damage.
means prohibition. It indicates actions, if any, that
mustn’t be done.
4. TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
5. This unit must be grounded.
CIRCUIT DIAGRAM
6. Check that the hood is correctly installed, since
incorrect installation could result in the range hood
becoming detached and falling off.
7. Connect only to an AC120 Volt power source or
the range hood could result in fire, electric shock,
and damage.
DIMENSIONS
CAUTION:
WARNING:
WARNING:
Unit: inch (mm)
NAMES OF PARTS
RANGE HOOD LOCATION
1
The range hood must be installed
just above the cooktop.
2
The minimum distance from the
cooking surface to the bottom of the
range hood must be 24".
3
The total weight of the ECP-360
range hood unit is 86.0 lbs. (39 kg)
4
Power requirements are:
AC120 V, 60 Hz, 3.0 Amp
• Check that the hood is correctly installed, since incorrect installation could
result in the detachment of the range hood and the unit could fall down.
• To protect hands from injury, wear working gloves when installing the
range hood.
CAUTION:
ACCESSORIES
24"(minimum)
Cook top
120V
60Hz
Connector
Connector
Connector
Connector
Connector
Connector
Motor
Red
Or
ange
Or
ange
White
White
White
White
White
White
Blac
k
Green
Blue
Blue
Bro
wn
Bro
w
n
Black
Purple
Purple
Black
Black
Black
Black
White
Black
Black
Grey
Grey
Grey
Yellow
Yellow
Yellow
Pilot Lamp
Lamp 50W
Lamp 50W
Fan Switch
Lamp Switch
Capacitor
3
Arrange the ends of 7” round duct and conduit so that they can connect
with the top of the range hood unit.
3. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Installation work and electrical wiring must be
done by a qualified person(s) in accordance with
all applicable codes and standards, including fire-
rated construction.
• Black to Black
• White to White
• Green to Green
WARNING:
6
With inserting the inner
frame into the outer
frame and the exhaust
port into the duct, lift up
the range hood unit and
pass the threaded rods
through the hanging
brackets as shown.
7
Fix the range hood unit
by adding 4 flange nuts
(not supplied) to the
threaded rods as shown.
Unit: inch (mm)
Duct
Conduit
Threaded rod
Inner Frame
Stringpiece
(Not Supplied)
40mm
Duct
Nut
Washer
Spring-
Washer
Ceiling
Beam
6
Secure the threaded rods by adding
washers, spring washers, and nuts
from the ends of the rods.
7
Set 4 flange-nut (not supplied) on the
threaded rods as shown for fixing the
supplied hanging brackets later.
50mm
Washer*
Inner Frame
Ceiling
Beam
Spring-Washer*
Nut*
*Not Supplied
Flange Nut
6
5
_
(2)
7
2. Range Hood Mounting
• Wear working gloves to avoid injury.
CAUTION:
1
Detach the tape on the exhaust
port, then with paying attention to
the shutter opening direction, fix it
using screws attached on the top
plate.
2
Detach the rectifier baffle
panel by loosening 2 fixing
screws, sliding it to dislocate
the keyholes from the
screws, and disengage it
from the catches.
Rectifier
baffle panel
Loosen 2 screws
to remove the filter
2
Loosen 2 screws to remove
the rectifier baffle panel
Filter
3
3
Detach the filters by
turning the fixing
knobs counter-
crockwise, and
disengaging them
from the supporting
groove.
Hanging bracket
Outer frame
5
4
Screw
4
Attach the outer frame to the range hood unit using 4 screws supplied.
5
Attach 4 hanging brackets supplied to the range hood unit and fix them
as shown. As the fixing screws are attached on the top plate, remove
them once and use for fastening the hanging brackets.
Exhaust port
Inner frame
Outer frame
Flange nut
Duct
6
7
Note:
Check that the range hood unit is fixed at the specified height
horizontally and adjust if not.
Screw
8
9
Non-flammable tape
Conduit
(Not supplied)
Nut
(Not supplied)
8
Fasten the outer frame
and inner frame using
4 screws removed
before as shown.
9
Make the duct joint
secure and air-tight
using non-flammable
tape such as duct tape,
etc (not supplied).
Wire cover
Screw
Nut
Conduit
Wire connector
Wire cover
Screw
Push to turn ON
Bulb
(Not supplied)
Filter
Rectifier baffle panel
4. Attaching Duct Cover
1
Attach the inner duct (front and rear).
Insert the upper edge of the inner duct into the gap between the inner
frame and ceiling with sliding on the guide frame on both sides, then
push the front and rear ducts until they are fixed by their roller catch.
Note:
Be careful not to attach the duct upside down.
2
Attach the outer duct (front and rear).
Place the outer duct on the range hood unit, and push the front and
rear ducts until they are fixed by their roller catch.
Note:
Be careful not to attach the duct upside down.
3
Fix the outer duct (front and rear) to the range hood unit using 4 screws
supplied as shown.
• Screw M5
×
10
Four (4) pcs.
• Screw M5.1
×
45
Eight (8) pcs.
4
Pass 4 threaded rods*
(not supplied) through
the holes of the
ceiling and put
washers, spring
washers, and nuts on
the rods, then fix
them to the beam.
(*
∅
12~14 anchor
bolt, length = duct
height - 40mm)
• Exhaust Port
One (1) pc.
Exhaust port
Shutter
opening direction
Tape
• Hanging Bracket
Four (4) pcs.
