Fuji Electric PXG5 Instruction Manual Download

Page: 1 / 20

– 1 –

Thank you for purchasing the Fuji Digital temperature Controller.

Once you have confirmed that this is the product you ordered, please use it in accordance with the follo wing instructions.

For detailed information on operating this equipment, please refer to the separate operations manual.

In addition, please keep this instruction manual within easy reach of the actual person using this equipment.

CAUTION

The contents of this manual are subject to change without notice.

This manual is complied with possible care for the purpose of accuracy, however, Fuji Electric

Systems shall not be held liable for any damages, including indirect damage,

caused by typographical errors, absence of information or use of information in this manual.

Please Read First (Safety Warnings)

Please read this section thoroughly before using and observe the mentioned safety warnings
fully. Safety warnings are categorized as “Warning” or “Caution”.

Warning

1-1

Limitations in Use

This product was developed, designed and manufactured on the premise that it would be used
for general machinery.
In particular, if this product is to be used for applications that require the utmost safety as
described below, please take into consideration of the safety of the entire system and the
machine by adopting such means as a fail-safe design, a redundancy design as well as the
conducting of periodical inspections.

•

Safety devices for the purpose of protecting the human body

•

Direct control of transportation equipment

•

Airplanes

•

Space equipment

•

Atomic equipment, etc

Please do not use this product for applications which directly involve human lives.

1-2

Installation and Wiring

●

This equipment is intended to be used under the following conditions.

●

Between the temperature sensor and the location where the voltage reaches or generates
the values described below, secure clearance space and creepage distance as shown in
the table below.
If such space cannot be secured, the EN61010 safety compliance may become invalid.

●

For the above, if voltage exceeds 50Vdc (called danger voltage), grounding and basic insulation
for all terminals of the equipment, and auxiliary insulation for digital outputs 1 to 3 is required,
Note that the insulation class for this equipment is as follows. Before installing, Please confirm
that the insulation class for equipment meets usage requirements.

Basic insulation (1500VAC)
Functional insulation (500VAC)
No insulation

•

In cases where damage or problems with this equipment may lead to serious accidents,
install appropriate external protective circuits.

•

As this equipment does not have a power switch or fuses, install them separately as nec-
essary. Fuse should be wired between main power switch and this equipment. (Main
power switch: Bipolar breaker, fuse rating: 250V 1A)

•

For power supply wiring, use wire equal to 600V vinyl insulated wire or above.

•

To prevent damage and failure of the equipment, provide the rated power voltage.

•

To prevent shock and equipment failure, do not turn the power ON until all wiring is complete.

•

Before turning on power, confirm that clearance space has been secured to prevent shock
or fire.

•

Do not touch the terminal while the machine is on. Doing so risks shock or equipment errors.

•

Never disassemble, convert, modify or repair this equipment. Doing so risks abnormal
operation, shock or fire.

•

Output relay is the part has a limited life. When output relay contact comes to the end of
its life, it might remain on-state, or off-state. For safety, use a protective circuit outside.

1-3

Maintenance

•

When installing or removing the equipment, turn the power OFF. Otherwise, shock, oper-
ational errors or failures may be caused.

•

Periodic maintenance is recommended for continuous and safe use of this equipment.

•

Some parts installed on this equipment have a limited life and/or may deteriorate with age.

•

The warranty period for this unit (including accessories) is one year, if the product is used
properly.

Caution

2-1

Cautions when Installing

Please avoid installing in the following locations.

•

Locations in which the ambient temperature falls outside the range of –10 to 50°C when
equipment is in use. (If the power supply is 200V AC, the recommended maximum ambi-
ent temperature is 45°C.)

•

Locations in which the ambient humidity falls outside the range of 45 to 90% RH when
equipment is in use.

•

Locations with rapid temperature changes, leading to dew condensation

•

Locations with corrosive gases (especially sulfide gas, ammonia, etc.) or flammable gases.

•

Locations with vibration or shock directly.

•

Locations in contact with water, oil, chemicals, steam or hot water.
(If the equipment gets wet, there is a risk of electric shock or fire, so have it inspected by
Fuji distributor.)

•

Locations with high concentrations of atmospheric dust, salt or iron particles.

•

Locations with large inductive interference, resulting in static electricity, magnetic fields or noise

•

Locations in direct sunlight.

•

Locations that build up heat from radiant heat sources, etc.

Warning

Mishandling may lead to death or serious injury.

Caution

Mishandling may cause injury to the user or property damage.

Fuji Electric Co., Ltd.

International Sales Div
Sales Group
Gate City Ohsaki, East Tower 11-2, Osaki 1-chome,
Shinagawa-ku, Tokyo 141-0032, Japan
http://www.fujielectric.com
Phone: 81-3-5435-7280, 7281 Fax: 81-3-5435-7425
http://www.fujielectric.com/products/instruments/

INP-TN1PXG5/9e-E

Confirming Specifications and Accessories

Before using the product, confirm that it matches
the type ordered.
(For model code, please refer to page 19.)
Confirm that all of the following accessories are
included.

Temperature Controller

1 unit

Instruction Manual

1 copy

Mounting Fixture

2 pcs

I/V Unit (250

Resistor)

1 pc

Waterproof packing

1 pc

Unit nameplate