You can change the ring tone length after the
ring tone melody is finished. To do this press
the PROG button, until the desired ring tone
length is reached.
3. Now press the transmission button, for which
you want to use these settings. The device will
confirm that the transmission code has been
programmed successfully by playing an
acknowledgement signal and a brief flashing
of the programming and loudspeaker button.
Once completed, the device will automatically
switch back to operation mode.
Repeat step 1 to 3 to program additional
transmission codes.
Note:
In case no transmission code is confirmed
within a period of 30 seconds during program-
ming, the radio bell will automatically switch back
to operation mode.
Any programming operation can be canceled by
pressing the loudspeaker button.
In case an additional transmission code is
received and all 32 memory positions have been
used up a warning signal will play for about four
seconds. No additional transmission code will be
programmed. The device will switch back to
operation mode.
Wall outlet
Loudspeaker
Loudspeaker
button
Programming button
Flashlight
GB
F/B (PL)
D(A/NL/S/N)
CH
Safety Advice
Models
Intended Use
Function
Select/Change Ring Tone and
Ring Tone Length
Start Up
Package Content
NZ80122
868.30 MHz
D
The device may only be operated indoors and
only as a radio bell and as wall outlet for mains
consumer load or low voltage consumer load.
The manufacturer will not be liable for damage
caused by improper or inappropriate use
.
You can specify a ring tone melody and ring tone
lenght for each transmitter button. Select the
desired settings on the radio bell and confirm by
learning the transmission code (step 1 to step 3).
Please note that subsequent changing of the
ring tone and the ring tone lenght for
transmission codes already learned is not
possible. The transmission code for which
you would like to change the settings, must be
deleted
(see section “Delete transmission code")
and memorized again with new settings.
1. Press the programming button of the radio bell
(approx. 5 seconds). The programming button
will flash slowly and the device will play an
acknowledgement signal.
Memorize the transmission code now, if you
want to use the radio bell with factory settings
(see step 3).
Continue with step 2 and step 3, if you would
like to select another ring tone or change the
ring tone length.
2. Select the desired ring tone by repeated
pressing of the PROG button .
The Plug-In Radio Bell NZ80122 receives Easy-
wave transmission codes from programmed hand
transmitters or wall transmitters. Once the
transmission button is pressed, a ring tone will
play and/or a light will begin to flash.
The wall outlet of the radio bell can be used as a
mains output socket for any electric device.
(230 V AC /50 Hz, bis 16 A)
A total of 32 transmission codes can be
programmed into the unit. A specific ring tone and
ring tone length can be allocated to each
transmission code.
Three different melodies are available as ring
tones: Westminster, March, Ringing Bell
The ring tone length can be set at a maximum
of 60 seconds, which is defined by the number
of repititions of the melody.
Five different combinations of gong volumes
and flashing lights can be selected:
-
Quiet and flashing light
-
Loud and flashing light,
-
Muted (only flashing light),
-
Quiet without flashing light,
-
Loud without flashing light.
From the factory, the radio bell is set to the march
melody and at the volume “quiet / flashing light".
1. Plug the radio bell into any wall outlet, you can
hear an acknowledgement signal.
2. A transmission code is assigned to each
button of the radio transmitter. Transmit the
trasmission codes of the transmitter to the
radio bell (see section “Ring tone and ring tone
length select/change“).
Caution:
Make sure that there is no interference
with the wireless connection. Do not mount the
device in a distribution box, metal casings or in
direct proximity to large metal objects.
Wall outlet radio gong NZ80122,
operating instructions
Please read these instructions
carefully before using the device!
We do not accept any liability for personal injury
or damage to property caused by incorrect
handling or non-observance of the safety
instructions!
Observe the valid laws and regulations as well
as the manufacturer's instructions
Attention!
Observe the admissible supply
voltage and the maximum contact load of the
wall outlet (16 A, 230 V AC / 50 Hz)!
Have malfunctioning devices checked by the
manufacturers!
Do not open the appliance's casing!
for the
devices to be operated!
Do not make any unauthorized alterations or
modifications to the unit!
Do not plug one Plug-In Radio Bell into
another.
The Plug-In Radio Bell is only de-energized
when it is disconnected from the mains
supply.
The Plug-In Radio Bell must be easily
accessible.
PROG
PROG
select ring tone
transfer factory setting:
or
select ring tone length
press the
PROG-button
repeatedly, until
desiredring tone
is played.
keep PROG-
button pressed for
the desired length
of the ring tone.
> 5 s
press send buton
Westminster
March
Ringing Bell
PROG
PROG
GB
Plug-In Radio Bell NZ80122
WWW.FUHR.DE
