background image

NOTICE

 - 

This service data sheet is intended for use by persons having electrical and mechanical training and a level of knowledge of these

subjects generally considered acceptable in the appliance repair trade.  The manufacturer cannot be responsible, nor assume any liability for
injury or damage of any kind arising from the use of this data sheet.

SAFE SERVICING PRACTICES

To avoid the possibility of personal injury and/or property damage, it is important that safe servicing practices be observed.  The following are examples, but
without limitation, of such practices.

1.

Before servicing or moving an appliance remove power cord from electrical outlet, trip circuit breaker to OFF, or remove fuse.

2.

Never interfere with the proper installation of any safety device.

3.

GROUNDING:  The standard color coding for safety ground wires is GREEN or GREEN WITH YELLOW STRIPES.  Ground leads are not to be used
as current carrying conductors.  It is extremely important that the service technician reestablish all safety grounds prior to completion of service.
Failure to do so will create a potential safety hazard.

4.

Prior to returning the product to service, ensure that:
• All electric connections are correct and secure.
• All electrical leads are properly dressed and secured away from sharp edges, high-temperature components, and moving parts.
• All uninsulated electrical terminals, connectors, heaters, etc. are adequately spaced away from all metal parts and panels.
• All safety grounds (both internal and external) are correctly and securely reassembled.

OVEN CALIBRATION

Set the electronic oven control for normal baking at 350°F.  Obtain an average oven temperature after a minimum of 5 cycles.  Press CANCEL or CLEAR
to end bake mode.

P/N  316218502 (0301)

SERVICE DATA SHEET

Gas Ranges with Electronic Oven Control

RTD SCALE

Temperature (°F)

Resistance (ohms)

32 ± 1.9

1000 ± 4.0

75 ± 2.5

1091 ± 5.3

250 ± 4.4

1453 ± 8.9

350 ± 5.4

1654 ± 10.8

450 ± 6.9

1852 ± 13.5

550 ± 8.2

2047 ± 15.8

650 ± 9.6

2237 ± 18.5

900 ± 13.6

2697 ± 24.4

ELECTRONIC OVEN CONTROL (REAR VIEW)

IMPORTANT

DO NOT REMOVE THIS BAG

OR DESTROY THE CONTENTS

WIRING DIAGRAMS AND SERVICE

INFORMATION  ENCLOSED

REPLACE CONTENTS IN BAG

ELECTRONIC OVEN CONTROL FAULT CODE DESCRIPTIONS

Note: Only two fault codes are displayed by this control - F1 or F3. Generally, F1 display implies the electronic oven  control itself has detected an
internal malfunction.  F3 implies the control has detected a sensor probe failure. In either case, an alarm will accompany a displayed F1 or F3.

1.

Shorted keypad.

2.

Control's internal checksum may have become corrupted.

3.

Control has sensed a potential runaway oven condition. Control may
have shorted relay, RTD sensor probe may have gone bad.

1.

Open RTD sensor probe. Note: The EOC will initially display an F1
for this condition. The EOC thinks a runaway oven condition exists.

2.

Shorted RTD sensor probe. Note: The F3 for shorted probe should
only occur when the oven is active or when an attempt is made to
enter a mode.

Likely Failure Condition/Cause

Suggested Corrective Action

     Fault  Code

1.

Replace EOC.

2.

Disconnect power, wait 30 seconds and reapply power. If fault returns
upon power-up, replace EOC.

3.

Check RTD sensor probe and replace if  necessary. If oven is
overheating, disconnect power. If oven continues to overheat when
the power is reapplied, replace EOC. Severe overheating may require
the entire oven to be replaced, should damage be extensive.

1.

Check resistance at room temperature and compare to RTD sensor
resistance chart. If resistance does not match the chart, replace RTD
sensor probe.

2.

Check resistance at room temperature, if less than 500 ohms, replace
RTD sensor probe.

F3

F1

RESISTANCE

TEMPERATURE

DETECTOR

Reviews: