![background image](http://html.mh-extra.com/html/freestyle/shark-788/shark-788_instructions_2330970001.webp)
788 MAKO
WATCH INSTRUCTIONS
FEATURES
• CURRENT TIME (HR., MIN.,
& SEC.)
• DAY/MONTH/DATE
• CHRONOGRAPH WITH SPLIT
& LAP TIMES
• DUAL ALARMS ( 1 DAILY
REPEATING, 1 NON-
REPEATING REMINDER.)
• COUNTDOWN, COUNTDOWN
REPEAT, COUNTDOWN
CHRONO
LAP & COUNTDOWN CHRONO
SPLIT TIMERS
• DUAL TIME
• HOURLY CHIME
• OPTIONAL 24-HR. TIME
(MILITARY TIME. )
• WATER RESISTANT TO
300 FT. OR 100M
• NIGHT VISION™ ELECTRO-
LUMINESCENT BACKLIGHTING
NORMAL TIME MODE
( The term “Mode” means the
function status of the watch.) Normal
time mode shows hours, minutes,
seconds, day and date. To set time,
see operating instructions on How
to Set Normal Time.
KEY TO SYMBOLS
LT - Left Top (Light/Set)
LB - Left Bottom (Mode)
RT - Right Top (Start/Stop)
RB - Right Bottom (Reset)
HOW TO SET NORMAL TIME,
DATE AND 24-HOUR FORMAT
Note: If no buttons are pressed for
approximately ten seconds, the
watch will exit the setting mode.
From Normal Time mode, press and
hold the Light/Set button LT for
approximately three seconds; the
seconds digits will flash.
Pressing the Start/Stop button RT
will reset the seconds digits to 0. If
seconds are greater than 30, one
will be added to the minutes digit.
RB will display a lap time.
To stop chronograph, press
Start/Stop button RT. Reset the
chronograph to zero by pressing the
Reset button RB.
HOW TO SET AND OPERATE THE
ALARMS AND HOURLY CHIME
From normal time mode, press
Mode button LB twice to enter the
alarm mode. Normal time remains
on the lower row, alarm time on the
upper row. Pressing Reset button
RB will toggle between alarm 1,
indicated by the left “ ” flag, and
alarm 2, indicated by the right
“ ” flag. Alarm 1 is a daily,
repeating alarm, and alarm 2 is a
one time only reminder alarm.
Press and hold Light/Set button LT
for approximately three seconds to
enter alarm setting mode. The
minutes digit will flash. Press
Start/Stop button RT to advance the
flashing minutes digit.
Press Mode button LB to advance
tens of minutes. Press Start/Stop
button RT to advance the flashing
tens of minutes digit.
Press Mode button LB to advance
the hours digit. Press Start/Stop
button RT to advance the flashing
hours digit. While setting the flashing
hours digit, “A” or “P” is displayed
on the right side. “A” designates
a.m. and “P” designates p.m.
Press Light/Set button LT to exit the
alarm setting mode. To activate the
alarm while in alarm mode: Press
Start/Stop button RT to arm or
disarm the alarm “ ” and/or hourly
chime “ ”. Note the setting
sequence is: alarm on, chime on,
both alarms and chime on, both
alarms and chime off.
Again, press Reset button RB to
toggle between alarm 1 and alarm
2. Alarm 2 is set and activated the
same way as alarm 1.
= alarm 1 on.
= alarm 2 on.
HOW TO OPERATE THE
COUNTDOWN TIMER
Press Mode button LB three times
from the normal time mode to enter
the countdown timer mode. Normal
time will remain in the lower row and
the timer will appear on the upper
row. “ ” flag will be displayed.
(Minimum time setting is one minute;
maximum time setting is 99 hours,
59 minutes).
*Note: there are four timer functions
in this mode. To select between
these features, press Reset button
RB until the desired function (noted
by its respective flag) is displayed.
TIMER COUNTDOWN - “ ” flag
will be displayed. This function will
countdown from a preset time. When
the countdown time is reached, the
timer will beep and will automatically
reset to the preset time.
TIMER COUNTDOWN REPEAT-
Press Reset button RB; “ ” and
“ ” flags will be displayed. This
function will countdown from a
preset time. When the countdown
time is reached, the timer will beep,
automatically reset, and begin
counting down repeatedly until the
Start/Stop button RT is pressed.
TIMER COUNTDOWN CHRONO
LAP- Press Reset button RB,
“C ”, “LP” and ” ” flags will be
displayed. This function will
countdown from a preset time. When
the countdown time is reached, the
timer will beep and automatically
start a chronograph. This
chronograph has a chrono lap timer,
identical to that in the
chronograph/stopwatch “LP” mode.
TIMER COUNTDOWN CHRONO
SPLIT- Press Lap/Reset button RB;
“C”, “ ” and “ ” flags will be
displayed. This function will
countdown from a preset time. When
the countdown time is reached, the
timer will beep and automatically
start a chronograph. This
chronograph has a chrono split timer,
identical to that in the
chronograph/stopwatch “ ” mode.
To set the countdown time, press
and hold the Light/Set button LT for
three seconds. The minutes digit
will flash. To advance the flashing
minutes digit, press Start/Stop
button RT.
Press Mode button LB to advance
to the tens of minutes digits, and
hours digits. Press Start/Stop
button RT to advance the flashing
digit. When desired timer time is
set, press Light/Set button LT to exit
the setting mode. To start or stop
timer, press Start/Stop button RT.
To reset a stopped timer, press
Reset button RB.
To set minutes, press Mode button
LB; single minutes digit will flash.
To advance flashing minutes digit,
press Start/Stop button RT; hold for
rapid advance.
To set tens of minutes, press Mode
button LB; tens of minutes will flash.
To advance flashing tens of minutes
press Start/Stop button RT; hold for
rapid advance.
Continuing through the setting
mode, the setting sequence is a
continuous loop of: seconds • single
minutes • tens of minutes • hours •
day/month/date • 12/24-hour mode,
and looping back to seconds. When
setting is complete, press Light/Set
button LT to return to normal time
mode.
HOW TO OPERATE
CHRONOGRAPH/STOPWATCH
The chronograph will record a
maximum of 99 hours, 59 minutes
and 59 seconds. Press Mode
button LB once from normal time
mode to enter the chronograph
mode. Normal time will remain on
the lower row, chronograph on the
upper row. The “C” flag will be
displayed.
Reset the chronograph to zero by
pressing Reset button RB. Press
the Light/Set button LT to switch
between Lap and Split mode.
(“LP” flag will be displayed for lap
mode and “C” flag will be displayed
for split time mode.)
Split time is the time elapsed since
the start of the chronograph. To
use the split time feature, “ ” flag
must be displayed. Press Start/Stop
button RT to start chronograph.
“ ” flag will begin flashing. Press
Reset button RB to view split time.
Chronograph will continue to count
while split time is displayed. To
release split time and return to
running chronograph, press Reset
button RB.
Each press of Reset button RB will
display a split time. To stop
chronograph, press Start/Stop
button RT. Reset the chronograph
to zero by pressing the Reset button
RB. Lap time is the time elapsed
since the previous lap. To use the
lap time feature, “LP” flag must be
displayed. Reset the chronograph
to zero by pressing the Reset button
RB. Enter Lap mode by pressing
Light/Set button LT. Press Start/Stop
button RT to start chronograph. “LP”
flag will begin flashing. Press Reset
button RB to view lap time. The
chronograph will start counting next
lap while lap time is displayed. To
release lap time and return to
running chrono, press Reset button
RB. Each press of Reset button