Freedom Lite Business 40/32 Installation Manual Download

Page: 1 / 30

Installation Manual

Freedom Lite Home and

Business

Range of Lithium Iron Phosphate Battery Modules

Manufactured By Freedom Won (Pty) Ltd

Kimbult Industrial Park, Unit C3 & C4

9 Zeiss Road

Laser Park, Honeydew

2040

South Africa

www.freedomwon.co.za

Technical and Installation Assistance – Contact:

Please contact your Freedom Won Distributor or Reseller Installer for technical and installation
support. A directory of Distributors and Reseller Installers is available at

www.freedomwon.co.za

For advanced support please contact

[email protected]

Update Record:

Revision

Number

Update Summary

Updated By

Date of Issue

Incorporated new model names and warranty

to reflect guaranteed performance at 80%

average DoD

Antony English

28 April 2020

Summary of Contents for Lite Business 40/32































Search results

Summary of Contents for Lite Business 40/32

Reviews:

Related manuals for Lite Business 40/32

Brands by name

Popular brands

Freedom Lite Business 40/32, Installation Manual

Search results

Summary of Contents for Lite Business 40/32

Reviews:

Related manuals for Lite Business 40/32

Brands by name

Popular brands