background image

 

 

FS-50 Alarm Combo System 

INSTALLATION HANDBOOK: 

 

INTRODUCTION 

 

 
Congratulations  on  your  choice  of  a  Crimestopper  combination  alarm  &  remote  engine  starter  with  Data  Port 
Technology 

 

This  installation  book  is  designed  for  the  installer  or  individual  with  an  existing  understanding  of 
automotive electrical systems, along with the ability to test and connect wires for proper operation.  To ease 
installation,  we  suggest  that  you  READ  THIS  MANUAL  before  beginning  your  installation.    This  book  is 
provided as a GENERAL GUIDELINE and the information contained herein may differ from your vehicle. 

 

DISCLAIMER: 
Crimestopper Security Products, Inc. and its vendors shall not be liable for any accident resulting from the 
use  of  this  product.    This  system  is  designed  to  be  professionally  installed  into  a  vehicle  in  which  all 
systems and associated components are in perfect working condition. 

 
 

TECHNICAL SUPPORT (800)-998-6880 
Monday - Friday 8:00am - 4:30pm Pacific Time 

 

Website: www.crimestopper.com 

 

CRIMESTOPPER SECURITY PRODUCTS, INC. 
1770 S. TAPO STREET 
SIMI VALLEY, CA. 93063 

 

REV  12.2008 
 

This  device  complies  with  FCC  Rules  part  15.  Operation  is 
subject to the following two conditions: 1) This device may not 
cause  interference,  and  (2)  this  device  must  accept  any 
interference  that  may  be  received,  including  interference  that 
may  cause  undesired  operation.    The  manufacturer  is  not 
responsible  for  any  radio  or  TV  interference  caused  by 
unauthorized 

modification 

to 

this 

equipment. 

Such 

modification  could  void  the  user's  authority  to  operate  the 
equipment.

 

Summary of Contents for ALARM COMBO SYSTEM FS-50

































Reviews: