Usage and placement:
Specifications:
Thank you for purchasing the FLACARP
SENS detector. This small device will
make it easier for you to guard your
equipment. After detecting shocks
or position changes, it sends a signal
to your FLACARP receiver, where an
alarm sounds.
The FLACARP SENS micro-sensor place
on the guarded object (with magnet,
velcro, or just lay ...), or put in the guard-
ed object (backpack, bag on a bike, mo-
torcycle). The location is arbitrary.
After pressing the button and count-
ing down 20 sec. detects shocks and
change of position. If the object is ma-
nipulated, the SENS sends a wireless
signal to the receiver where the alarm
sounds. The sensor can guards e.g.
boat, backpack, bivouac, bike, motor-
cycle, car, it can be placed at the cabin
door, caravan ...
■ Shock and position change detection
in all axes (X, Y, Z)
■ Three levels of sensitivity
■ Powered by 3V CR2450 batteries
■ Saves battery, very low consumption
current during guarding
■ Transmission frequency: 868MHz
■ Range: up to 200 meters in open
space
■ Compatibility: with FLACARP receivers
■ Dimensions: 4 x 4 cm, height 1.5 cm
■ Weight (with battery): 25 grams
■ Protection: IP62
Prepare and activation:
Deactivation:
Sensitivity adjustment:
Due to application, the sensor can be
equipped with a magnet or velcro from
the rear side (the other side of the vel-
cro stick to the guarded object). Then
the sensor can be easily removed and
used for guarding more items.
Activation:
After placement on a
guarded object, press the button, and
the green LED starts flashing - after
about 20 seconds, the sensor starts
guarding. If manipulation is detected,
the device sends an alarm signal. To
avoid continuous transmission is the
sensor blocked after the third detec-
tion for approx. 1 minute. After this time,
the sensor guards again.
To turn off the sensor, press the button
for one second (red LED lights up briefly).
An alarm signal is sent when the device is
switched off (This is in case an unauthor-
ized person turns the device off).
Hold the button for 3 seconds until the
green LED starts to flash. You can now
rotate between three sensitivity levels
by the short button press:
a)
LED flashes one time - lowest
sensitivity
b)
LED flashes two times in a row - me-
dium sensitivity
c)
LED flashes three times in a row -
high sensitivity
After sensitivity is selected, you can
save and exit the sensitivity adjust-
ment mode by holding the button for 1
sec - the green LED will light up briefly,
saved.
Pairing with the receiver (pairing is
the same as by bite alarms):
Alarm signaling on the receiver:
a)
At the same time, press and hold the
PLUS and MINUS buttons on the receiver
for 1 second. The white LED on position 1
lights up.
b)
Use the PLUS and MINUS buttons to
move to a free position where you want to
save the sensor.
c)
Switch on the FLACARP SENS mi-
cro-alarm - simulate the alarm after the
countdown (change position of the sen-
sor). The sensor sends a signal, and the re-
ceiver saves it. Pairing is completed.
If a deep tone sounds during pairing and
the white LED is still on (the sensor has not
been paired), the position is already occu-
pied, or the same sensor is already saved
in the receiver‘s memory. Other accesso-
ries (bite alarms) can be paired same way.
Up to 12 channels are available, two devic-
es for each LED. The first six are lit with a
white LED while learning, and the second
six with a red LED.
The significant fluctuating tone and
flashing red and blue LEDs signal an
alarm on the receiver. The alarm can be
muted by pressing the MINUS button.
Pressing the MINUS button again will
switch off the optical signaling (receiver
RX7 can be muted with the main but-
ton). With a next manipulation, is alarm
reactivated.
+420 731 115 151 [email protected] flacarp.com flacarp flacarp tfe.cz
M i c r o - a l a r m -
F L A C A R P S E N S
INSTRUCTIONS FOR USE
P 1
