background image

Manual for motor FM_VM R5_R7 ( Date of publication 01/2018)

 

 

FIALA PROP s.r.o,  Vysoká 56,  75641 LEŠNÁ ,  Czech Republic , e-mail: [email protected] 
www.fialaprop.com

  

Page 1 

 

         

                                        

 

 

 

  

     

 

 

 

   250 R5 

 

 

 

420 R5  

 

    800 R7 

Volume: 250 ccm 

 

 

Volume: 420 ccm 

   Volume: 800 ccm 

Bore: 42 mm   

 

 

Bore: 47 mm   

   Bore: 52 mm 

Stroke: 32 mm 

 

 

Stroke: 48,5 mm 

   Stroke: 52 mm 

Weight: 5,6 kg  

 

 

Weight: 11,8 kg 

   Weight: 28,2 kg 

 

Manual for radial motors  VM R5-250, R5-420, R7-800 produced by  
Fiala Prop, s.r.o. company 

 

Safety instructions. 

It is imperative that you read before handling and using the motor this notice and study 
the motor manual. If you not find answers to your questions, consult with a more 
experienced colleague, contact your dealer engine or contact the manufacturer directly. 

Remember that engine, what you bought is not a toy and is designed only to drive the 
airplane models under the terms of the instructions for assembly and use. In the case of 
our products, it is a  big volume motors and performance, thus this requirement is more 
important. 

Summary of Contents for Valach Motors VM R5-250










Reviews: