background image

Manual for motor FM 170 B2 - FS ( Date of publication 06/2016)

 

 

FIALA PROP s.r.o,  Vysoká 56,  75641 LEŠNÁ ,  Czech Republic , e-mail: [email protected] 
www.fialaprop.com

 

 

Page 1 

 

 

 

 

Manual for motor FM 170 B2-FS 

Safety instructions. 

It is imperative that you read before handling and using the motor this notice and study 
the motor manual. If you not find answers to your questions, consult with a more 
experienced colleague, contact your dealer engine or contact the manufacturer directly. 

Remember that engine, what you bought is not a toy and is designed only to drive the 
airplane models under the terms of the instructions for assembly and use. In the case of 
our products, it is a  big volume motors and performance, thus this requirement is more 
important. 

If the motor or the whole model with this motor provide another person, tell him safety 
instructions and operating instructions. If you do these guidelines and / or instructions lost 
or destroyed, you can re-download them from our website. 

 

Please take great care in securing the motor in model and check it regularly. Likewise, 
check the propeler mounting screw. 

Summary of Contents for FM 170 B2-FS









Reviews: