EN / SPECIFICATION
HEADLAMP
Light source
COB Led + Red Led
Power supply
Li-Po 3.7V 1200 mAh
MODES
OUTPUT
RUN TIME
DISTANCE
HIGH
900 lm
1 h 30 min
90 m
MEDIUM
500 lm
3 h
70 m
LOW
100 lm
9 h
30 m
STROBE
-
-
-
COB LED HIGH
100 lm
10 h
13 m
COB LED LOW
50 lm
15 h
5 m
RED LED FLASHING
-
-
-
SENSOR MODE HIGH
900 lm
-
-
SENSOR MODE LOW
500 lm
-
-
Dimensions
64,5 x 43,3 x 40 mm
Weight
90,5 g
Impact resistance
1 m
WORKSHOP LIGHT
Light source
COB Led
Power supply
Li-Ion 3600 mAh
MODES
OUTPUT
RUN TIME
DISTANCE
HIGH
500 lm
4 h
25 m
MEDIUM
250 lm
8 h
18 m
LOW
125 lm
16 h
10 m
Dimensions
64,5 x 43,3 x 40 mm
Weight
190 g
Impact resistance
1 m
Thank you for choosing a Mactronic® product. Proper operation and main-
tenance guarantee the product’s high durability and reliability. Please read
the operating manual and keep it for reference, because it contains impor-
tant information about safety and operation of the product.
NOTICE
It is not recommended to use the flashlight for purposes other than in-
tended. The manufacturer explicitly voids the warranty if the flashlight has
been used for other than its intended purpose.
FLASHLIGHT OPERATION
WORK LAMP:
To turn on the flashlight, press the right button located on the
front of the flashlight. The flashlight will turn on in low mode (LOW). Sub-
sequent button presses will cycle through the modes in the following order:
LOW
→
MEDIUM
→
HIGH
→
OFF. During operation and while charging, the
battery level is indicated by 4 blue LED lights. At the rear of the flashlight,
there is a strong magnet and a collapsible handle with a clip, allowing for
easy attachment of the flashlight to a work area without the need to hold
it in hand.
HEADLAMP:
To turn on the headlamp, press one of the available power
buttons (either the right or left). Pressing the right power button will im-
mediately turn on the flashlight. Hold down the left power button for 3 se-
conds until the flashlight turns on. For the right power button, the available
functions/modes are activated in the following sequence: LOW
→
MEDIUM
→
HIGH
→
STROBE
→
COB HIGH
→
COB LOW
→
RED LIGHT FLASHING
→
OFF. If the mode change button is not pressed for 8 seconds, the next
press will turn off the light. Restarting will cycle back to the first mode
in the sequence. To activate the motion sensor mode, hold down the left
power button for 3 seconds. The motion sensor mode is a standby mode
that allows you to turn the light on or off with a hand motion from the left
side in front of the headlamp, within a detection range of up to 4 cm. For
the left power button, the available functions are activated in the following
sequence: SENSOR MODE HIGH
→
SENSOR MODE LOW
→
SENSOR MODE
COB HIGH
→
SENSOR MODE COB LOW
→
OFF. If the button is not pres-
sed during mode change for 8 seconds, the next press will turn off the
headlamp. To reactivate the motion sensor mode, hold down the left button
for 3 seconds. After turning on or off, the headlamp will indicate the battery
level using 4 blue LED lights for 5 seconds. This battery level indicator is
located on the front of the housing.
CHARGING
WORK LAMP:
To charge the device, uncover the rubber cover of the USB-C
port located at the bottom of the flashlight. Connect the provided USB-US-
B-C cable to a USB wall charger, a computer’s USB port, or a Power Bank
station. Attach the other end of the cable to the USB-C port. The active
charging process will be indicated by the illumination of the 4-step charging
indicator, where a flashing LED indicates the current level of charge. Once
the charging process is complete, all indicator LEDs will remain steadily lit.
After disconnecting the charging cable, cover the port with the rubber co-
ver to protect it. You can also partially charge other devices by connecting
them to the USB port of the flashlight. To do this, uncover the rubber cover
of the USB-C port located at the bottom of the flashlight. Connect the provi-
ded USB cable to the USB port of the flashlight. Attach the other end of the
cable to the device you want to charge. The active charging process of the
external device will be indicated by the 4-step charging indicator.
HEADLAMP:
To charge the device, uncover the rubber cover of the USB-C
port located at the bottom of the headlamp. Connect the provided USB-
-USB-C cable to a USB wall charger, a computer’s USB port, or a Power
Bank station. Attach the other end of the cable to the USB-C port of the
headlamp. The active charging process will be indicated by the illumination
of the 4-step charging indicator, where a flashing LED indicates the current
level of charge. When the charging process is complete, all indicator LEDs
will remain steadily lit. After disconnecting the charging cable, cover the
port with the rubber cover to protect it.
CAUTION!
Make sure you use only genuine parts designed for Mactronic® flashlight.
Using spare parts from other manufacturers may affect the quality and
parameters of the product. The rechargeable batteries used in this product
may be subject to re-processing. Pursuant to the EU’s WEEE regulation,
storage batteries must not be disposed of with normal household waste.
Instead, they must be disposed of at designated battery collection points.
Contact the management of your local waste collection company for advice
on the required ways and types of re-processing, or other instructions.
GENERAL INFORMATION
Modifications and repairs:
Unless authorized by Mactronic® in writing, any modifications and user at-
tempts at home repairs will automatically void the warranty.
Mactronic® warranty:
Mactronic® covers the product with a 2-year warranty for any manufactu-
red defects in material and/or workmanship. The warranty does not cover
the product, rust, unauthorized modifications, improper storage, damage
from falls, improper handling, corrosion from leaking batteries, and use of
the product to its intended purpose.
USING AND HANDLING THE BATTERY
To reduce the risk of fire, electrocution or other bodily harm, carefully read
the flashlight’s operating manual.
• Always make sure the battery’s polarity is correct.
• Remove the batteries if the flashlight is stored for extended time.
• Do not recharge alkaline batteries.
• Do not dispose of the batteries in fire.
• Keep the batteries out of reach of the children.
• Do not force the batteries open.
• Keep the flashlight away from UV radiation, humidity and chemical
products.
WORKSHOP LAMP KIT
FWS0007
