![background image](http://html.mh-extra.com/html/extreme-networks/rola-59-401/rola-59-401_assembly-instructions-manual_2454464001.webp)
Product Code:
Product Name:
Cequent Consumer Products
Solon, OH 44139 USA
www.rolaproducts.com
59 401
4 Place Bike Carrier - Folding
LOADING INSTRUCTIONS:
1.
Place the bike rack receiver into your receiver hitch. Fit rack as close to
vehicle as possible.
2.
Secure rack with 5/8” hitch pin and clip. (See Diagram 3)
3.
The bikes are loaded onto the rack alternating each bike, with the anti-sway
cradle being closest to the seat tube. (See Diagram 4)
4.
Secure the bikes by pulling the bungee straps over the top of the bike frame.
The anti-sway straps wrap around the seat tube prevent the bike from
swaying.
5.
Check the bungee straps periodically and after stopping to insure that they are
still tight and that someone has not released them. NOTE: Insure all locks are
locked, that all pins are secured, and that all bungee straps are properly
attached prior to moving the vehicle. Failure to do so will void the warranty.
INSTRUCTIONS FOR FOLDING THE RACK:
1.
Insert the key into the lock mechanism and turn to release the lock pin.
2.
Remove the ½” pin and clip.
3.
Pull support tube firmly upwards until lower pin slides to the top of its slot.
4.
Lower the tube slowly back until support tube rests on the stop plate.
NOTE: Do not drop or let the support tube fall freely. Make sure that your
hands and fingers are clear of the hinging area during this operation.
5.
To restore the rack to the upright position, do reverse procedure. Remove
the key from the lock and push the center of the cylinder in to engage the
lock pin. A notable click will indicate that the pin is locked.
6.
Re-install ½” pin and clip. Check periodically to insure you have a solid fit
between the rack and the mounting location.
59401N Rev B 9-9-05
ASSEMBLY INSTRUCTIONS:
1.
Use key to unlock lock on Collar Bracket.
2.
Pull spring loaded release pin on side of Main Support tube, remove handle
mechanism, and rotate bike Support Arms into the
UP
position. Re-insert the handle
mechanism. Pull out the spring loaded release pin and push handle all the way
down. Let the spring loaded pin go so that it fully engages the handle mechanism.
3.
Slide the Collar Bracket onto the bike carrier Main Support tube in orientation shown
(see Diagram 1).
4.
Attach Collar Bracket to Main Support tube using one (1) ½” x 3-1/4” lg. hex bolt, two
(2) nylon flat washers, and locknut installed through the “slotted” hole in Collar
Bracket. Tighten locknut until it is snug against the flat washers.
5.
Install ½” Pin and Clip through hole directly above the lock on Collar bracket.
6.
Attach Receiver piece to Collar Bracket using two (2) ½” x 3” hex bolts through the
½” diameter holes (closest to end of tube). (See Diagram 2)
Tighten Receiver piece bolts to 75 Lb.-Ft.
7.
Lock Collar Bracket to Main Support tube so bike carrier is in the upright position.
Diagram 1
½” x 3-1/4” Hex Bolt
(2) Nylon Flat Washer
Locknut
“Slotted”
Hole
Collar Bracket
Main Support
Tube
Release Pin
Handle Mechanism
Drop of Oil
½” x 3” Hex Bolt
Locknut
(2) Places
Diagram 2
Collar
Bracket
Lock
Diagram 3
½” Pin & Clip
Anti-Sway
Cradle
Diagram 4
Diagram 5
5/8” Pin & Clip
Cequent Help Hotline: 1-800-234-6992
Please read all instructions carefully before assembly, installation and/or use of this product.