![background image](http://html1.mh-extra.com/html/exsys/ex-1083/ex-1083_manual_2452752001.webp)
6
5
Die EX
-
1083 ist mit 3 externen USB 2.0 Anschlüssen ausgestattet. Der serielle PCI
-
Bus unter-
stützt optimal die Leistung des schnellen NEC Chipset. Die USB Karte gewährleistet so eine
sichere Datenübertragung und exzellente Performance von bis zu 480Mbit/s! Die USB 2.0 PCI
Karten sind voll kompatibel mit Microsoft Windows Standard OpenHCD Treibern und sind nach
den Normen des USB Rev. 2.0 entwickelt worden. Sie haben einen Dual Speed USB Transcei-
ver. Sie unterstützen den 32
-
und 64
-
bit PCI
-
Bus mit 5 Volt und 3,3 Volt.
1
ANSCHLÜSSE
BESCHREIBUNG & TECHNISCHE DATEN
AUFBAU
Anleitung
Vers. 1.0 / 05.07.18
EX
-
1083
Kompatibilität:
PCI 32
-
bit oder PCI
-
X 64
-
bit, 33Mhz
Betriebssysteme:
Windows ME
/
2000
/
XP
/
Vista/ 7/ 8.x/ 10/ Server 20xx/ MAC/ Linux
Anschlüsse:
3x USB 2.0 A
-
Buchse extern
Lieferumfang:
EX
-
1083, Low Profile Bügel, Anleitung
Zertifikate:
J1
-
J3:
3x external USB 2.0 A
-
Port
J1
-
J3:
USB 2.0 Pin
‘
s
Pin
Signal
Pin
Signal
1
VCC
3
DATA+
2
DATA
-
4
GND
Achtung!
Bitte Stecker nie mit
Gewalt oder umgekehrt in
den Anschluss stecken!
HARDWARE
INSTALLATION
DRIVER INSTALLATION
If you are ready with the jumper settings, please proceed with the following installation instructions.
Because there are large differences between PC
’
s, we can give you only a general installation
guide for the card. Please refer your computer
’
s reference manual whenever in doubt.
1.
Turn off the power to your computer and any other connected peripherals.
2.
Remove the mounting screws located at the rear and/or sides panels of your Computer and
gently slide the cover off.
3.
Locate an available PCI expansion slot and then gently but firmly insert the card. Make sure
that the card is seated and oriented correctly.
4.
Then connect the card with a screw to the rear panel of the computer.
5.
Gently replace your computer
’
s cover and the mounting screws.
All OS
After the hardware installation, the operating system will recognize the device automatically and
install the drivers.
CHECK INSTALLED DRIVER
Open the
>Device manager<
.
Now you should see at
„
USB
-
Controller
“
the following new
entry's:
If you see this or a similar information the device is installed correctly.
NEC Driver (optional)
If you experience any performance problems or if you want to use older operating systems
which doesn't support USB 2.0 such as Windows 98SE. You can download the driver at our
website
www.exsys.de
or you can find the driver on our driver CD. Then you can install the
optional VIA Drivers as follows. The driver are available up to Vista.
Open and run the file
“
U2v2_1.exe
“
by double click on your mouse and follow the setup pro-
gram to finish installation process. After that shut down windows and follow the instructions for
the Hardware installation. After installing the card simply start your computer and the card will
be recognized automatically by your system.