![background image](http://html1.mh-extra.com/html/evercraft/776-2007/776-2007_manual_2442748001.webp)
776-2007
1
rev. 02/24/20
WARNING INFORMATION
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
WARNING: Indicates a hazardous situation which,
if not avoided, could result in death
or serious injury.
776-2007
CAPACITY: 2 TON
JACK STANDS
(PAIR)
WARNING
IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING
BEFORE USING THESE STANDS, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING
PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.
It is the responsibility of the owner to make sure all personnel read this manual prior to using these stands. It is also the responsibility of the stand owner to keep
this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost or not legible, contact Balkamp for replacements. If
the operator is not fluent in English, the product and safety instructions shall be read to and discussed with the operator in the operator's native language by the
purchaser/owner or his designee, making sure that the operator comprehends its contents.
THE NATURE OF HAZARDOUS SITUATIONS
The use of portable automotive lifting and support devices is subject to certain hazards that cannot be prevented by mechanical means, but only by the exercise of
intelligence, care, and common sense. It is therefore essential to have owners and personnel involved in the use and operation of the equipment who are careful,
competent, trained, and qualified in the safe operation of the equipment and its proper use. Examples of hazards are dropping, tipping or slipping of loads caused
primarily by improperly secured loads, overloading, off-centered loads, use on other than hard level surfaces, and using equipment for a purpose for which it was
not designed.
METHODS TO AVOID HAZARDOUS SITUATIONS
• Read, study, understand and follow all instructions before operating this device.
• Inspect the jack stands before each use. Do not use if damaged, altered, modified, in poor condition, or unstable due to loose or missing
components. Make corrections before using.
• User and bystanders must wear eye protection that meets ANSI Z87.1 and OSHA standards.
• Use as a matched pair only.
• Use only on a hard level surface capable of supporting the load.
• Stands are to be used in matched pairs to support one end of a vehicle only. Do not simultaneously support both ends or one side of a
vehicle.
• Center load on saddle. Do not use saddle lugs to support the load.
• Do not use jack stands beyond its rated capacity. Do not shock load.
• Maximum load capacity per matched pair shall not exceed the rated capacity of the individual stand.
• Apply the emergency brake, put the gear shift lever in park or in gear if a manual shift transmission, and chock the tires that will not be
lifted off the ground.
• Check the stands for solid contact with the ground and vehicle.
• Ensure both stands are set at same height and locking pawls are fully engaging the support column's teeth.
•
Do not crawl under vehicle when placing/removing stands.
• Consult the vehicle manufacturer for the proper frame support locations.
• No alterations shall be made to these stands.
• Failure to heed these warnings may result in serious or fatal personal injury and/or property damage.
WARNING:
This product can expose you to chemicals including nickel which is known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS
Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS, MAINTENANCE
INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS could cause accidents resulting in serious
or fatal personal injury and/or property damage.
WARNING
WARNING
WARNING
S
AFE
TY
STAND
AR
D
CO
MPL
IES
ITH
W
ASME PASE-2019