background image

 

Rev. 04/27/17 DR 

www.epvscreens.com

 

 

 

 

DarkStar® UST eFinity Series 

EDGE FREE

® 

Ultra-short throw Fixed Frame Screen

 

USER’S GUIDE 

 

Product Description: 

The 

DarkStar®  UST Series 

is an ultra-short throw fixed frame projection  screen that uses EPV’s EDGE 

FREE

®

  technology. It is designed for 

Ultra

-

Short Throw Projectors only, 

for use in environments where 

ceiling light cannot be entirely controlled

It includes an LED backlight kit and an  ultra-thin  bezel  to further 

enhance the frame appearance. 

 

 

Screen Maintenance 

Dust, dirt and scratches on the projection screen surface will affect the quality and performance of the 

projection image. For optimal results we advise to pay attention to the following instructions.

 

 

1) The screen surface has a horizontal lens structure. 

DO NOT

 wipe the screen up and down or in a circular 

motion.  
 

Wipe from left to right only

 
2) Please clean the dust on the screen surface with a soft brush or microfiber cloth (rough towel or cloth may 
damage the screen’s surface). 
 
3) Gently wipe the screen with a moistened microfiber cloth with mild soap diluted in water. 

 
Notes

 

The following precautions should be followed at all times to avoid damaging the material, which is 
not covered under warranty. 
 

 

Don’t 

touch

 the screen material to avoid leaving fingerprints. 

Use gloves when handling the material

 

Don’t 

scratch

 the material, as it will leave permanent markings on the screen’s surface. 

 

Don’t 

point 

to the screen material with a fingertip or other sharp objects to prevent damage to the 

material. 

 

Don’t 

use

 acetone, benzene, alcohol and any other organic solvents to clean the screen material. Using 

such chemicals will permanently damage the screen. 

Summary of Contents for EF100H-CLR











Reviews: