background image

EMPIRE

EMPIRE

Comfort Systems

INSTALLATION INSTRUCTIONS

AND

OWNER'S MANUAL

CAST IRON 

UNVENTED ROOM hEATER

MODELS

VFP30CA30(B,F,M,S,W)N-3

VFP30CA30(B,F,M,S,W)P-3

WATER  VAPOR:  A  By-PRODUCT  OF 

UNVENTED ROOM hEATERS

Water vapor is a by-product of gas combustion. An 

unvented room heater produces approximately one 

(1) ounce (30 ml) of water for every 1,000 BTU's 

(.3KW's) of gas input per hour. Refer to page 6.

WARNING: If not installed, operated and main-

tained  in  accordance  with  the  manufacturer's 

instructions,  this  product  could  expose  you  to 

substances in fuel or from fuel combustion which 

can cause death or serious illness.

This is an unvented gas-fired heater. It uses air 

(oxygen) from the room in which it is installed. 

Provisions for adequate combustion and ventilation 

air must be provided. Refer to page 7 .

This appliance may be installed in an aftermarket, 

permanently located, manufactured (mobile) home, 

where not prohibited by local codes. 
This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is not 

convertible for use with other gases.

The Heritage Cast Iron Stoves

GAS-FIRED

—  Do not store or use gasoline or other flamma

-

ble vapors and liquids in the vicinity of this or 

any other appliance.

—  WhAT TO DO IF yOU SMELL GAS

  •  Do not try to light any appliance.

  •  Do not touch any electrical switch; do not 

use any phone in your building.

  •  Immediately call your gas supplier from a 

neighbor’s  phone.  Follow  the  gas  suppli-

er’s instructions.

  •  If you cannot reach your gas supplier, call 

the fire department.

—  Installation and service must be performed by 

a qualified installer, service agency or the gas 

supplier.

WARNING: If the information in these instruc-

tions are not followed exactly, a fire or explosion 

may result causing property damage, personal 

injury or loss of life.

Installer:  Leave  this  manual  with  the  appli-

ance.

Consumer: Retain  this  manual  for  future  

reference.

Page 1

Summary of Contents for VFP30CA30 Series

































Reviews: