background image

www.Fisher.com

Fisher

 ENVIRO‐SEAL

 Packing System 

for Rotary Valves

Contents

Introduction

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scope of Manual

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Valve/Actuator Shaft Coupler

2

. . . . . . . . . . . . . . . . . .

Description

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removing the Actuator

3

. . . . . . . . . . . . . . . . . . . . . . .

Installing an ENVIRO‐SEAL Packing System

4

. . . . . . .

Other Considerations

11

. . . . . . . . . . . . . . . . . . . . . . .

Parts Ordering

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Kits

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Retrofit Kits

13

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Repair Kits

16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 1. Typical ENVIRO‐SEAL Packing System

W5882-1

W9058‐1

ROTARY

BUTTERFLY

Introduction

Scope of Manual

This instruction manual includes installation and parts information for Fisher ENVIRO‐SEAL live‐loaded packing
systems (see figure 1). These systems are available for Fisher rotary valves with 12.7 through 88.9 mm (1/2 through
3‐1/2 inch) shaft diameters. The system can be used with many rotary valves, as shown in tables 1 and 3. Refer to
appropriate valve and actuator instruction manuals for necessary information relating to the disassembly and
assembly of the valve and actuator. ENVIRO‐SEAL packing systems utilize a Belleville (coned‐disk) spring system.

Do not install, operate, or maintain the ENVIRO‐SEAL packing system, valve, actuator or accessories without being
fully trained and qualified in valve, actuator, and accessory installation, operation, and maintenance.

 To avoid personal

injury or property damage, it is important to carefully read, understand, and follow all the contents of this manual,
including all safety cautions and warnings. 

If you have any questions about these instructions, contact your 

Emerson

sales office

 before proceeding.

Instruction Manual

D101643X012

ENVIRO-SEAL System - Rotary Valves

February 2019

Summary of Contents for Fisher ENVIRO-SEAL





















Reviews: