background image

 

 

© 2018 Emerson Climate Technologies, Inc.

 

 
 
 
 
 

TABLE OF CONTENTS  

 

Safety 
 

Safety Instructions ................................................... 2 

  Safety Icon Explanation ........................................... 2 
  Instructions Pertaining to Risk of  
  Electrical Shock, Fire, or Injury to Persons ............. 3 
  Safety Statements ................................................... 4 

 
Introduction

 

  Product Description ................................................. 5 
  Theory of Drive Operation ....................................... 5 
  Agency Recognition ................................................. 5 
  Nomenclature .......................................................... 5 
 

Installation

 

  Drive Handling ......................................................... 5 
  Mounting .................................................................. 5 
  Drive Dimensions..................................................... 5 
  Wiring Diagram ........................................................ 5 
 

 

Operation & Function

 ............................................... 5 

     Hi-pot Procedure / Set-up ...................................... 5 
  Temperature & Humidity ......................................... 6 
  Pre-operation Checks ............................................. 6
  Power On/Off  ......................................................... 6 
  Communication Setting .........................................  6 
  Input Voltage and Input Current ............................. 6 
  Dynamic DC Bus Voltage Control by Buck ............ 6 
  Speed Control ......................................................... 6 
  Start-up ................................................................... 6 
  Shutdown ................................................................ 6 
 
 
 
 

 
 
 
 
  Fault Clearing ......................................................... 6 
  Lockout Faults ........................................................ 6 
  Stator Heat Control ................................................ 6  
  Status Indication ..................................................... 7 
     4 States of RGB LED (DS1-LED) ....................... 7 
     Rolling LED ......................................................... 7    
  Power Interrupt ....................................................... 7 
  Drive Configuration ................................................ 7 
  High Pressure Cut Out ........................................... 7 
  Drive Cooling .......................................................... 7 
  Drive Over Temperature Protection ....................... 7 
  Air Cooled Heat Exchanger ................................... 8 
  Cold Plate Heat Exchanger .................................... 8 
  Foldback ................................................................. 8 
  Troubleshooting ..................................................... 8 
  EMC Guidelines ..................................................... 8 
 

Figures 
 

Drive Assembly 3D

 

Wiring Diagram ....................... 9 

  Drive Assembly 2D Wiring Diagram ..................... 10 

 
Tables

 

  Communication Connector Pin Definition ............ 11 
  Sensor Connector Pin Definition .......................... 11 

 
Addendum

 

 

 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 

 

AE8-1429 R1 

January 2018 

EV2 Three Phase Series Variable Speed Drives 

517-625V, 8.0 kW 

These commodities, technology or software, are subject to the U.S. Export Administration Regulations (EAR).  
Diversion contrary to U.S. law is prohibited. ECCN: EAR99 

Summary of Contents for Copeland EV2 Series




























Reviews: