background image

 

Bedienungsanleitung 

Manual 

MAN_FIMP XL-E 

Version:  1.0.8 

/ 13.11.2020 

Freigabe: 

U.A. 

Seite 1 von 9 

 
 

 

 

 

FIMP-XLE 

Art.-Nr.: 0 6180 0 U VV WW X YY ZZ 9-00 

 

 

 

eks Engel FOS GmbH & Co. KG 
Schützenstraße 2-4 
57482 Wenden-Hillmicke 
Germany 
 
Tel:        +49 (0) 2762 9313-600 
Fax:       +49 (0) 2762 9313-7906 
E-Mail:     [email protected] 
Internet:    www.eks-engel.de 
 

 

Rechtliche Hinweise 

 

Legal Notice 

 

Diese Anleitung enthält wichtige Anmerkungen und Warnungen, deren Nichtbe-
achtung zu ernsthaften Personen- oder Anlageschäden führen kann. Bitte lesen 
Sie die Anleitung vor Inbetriebnahme des Gerätes aufmerksam durch. Ord-
nungsgemäßer Transport, korrekte Lagerung und Installation sowie sorgfältige 
Bedienung und Instandhaltung des Geräts sind entscheidend für den sicheren 
Betrieb. 
 

 

 
This manual contains important notes and warnings which, if ignored, can lead to 
serious personal injury or system damage. Please read these instructions 
carefully before using the device. Proper transport, correct storage and installation 
as well as careful operation and maintenance of the device are crucial for safe 
operation.

 

 

Summary of Contents for FIMP XL-E










Reviews: