Eela Audio Logos Manual Download

Page: 1 / 27

Manual Logos

EELA AUDIO Parmentierweg 3

Rev. 6

(July 2001)

5657 EH Eindhoven, the Netherlands

Main v1.43

PART A: INSTALLATION OF THE LOGOS

The desktop console ............................................................................................................ 2

1.1 Outlook --------------------------------------------------------------------------------------------------------------------2

1.2 Fader section ------------------------------------------------------------------------------------------------------------3

1.3 Monitor section ----------------------------------------------------------------------------------------------------------3

1.4 Function keys------------------------------------------------------------------------------------------------------------4

1.5 Numeric keypad---------------------------------------------------------------------------------------------------------4

1.6 Transport control section ---------------------------------------------------------------------------------------------5

1.7 Jog / shuttle wheel------------------------------------------------------------------------------------------------------5

The rack-unit (D902).............................................................................................................. 6

2.1 Front side connectors--------------------------------------------------------------------------------------------------6

2.2 Rear side connectors --------------------------------------------------------------------------------------------------7

LogosTool software .............................................................................................................. 9

3.1 Connect procedure -----------------------------------------------------------------------------------------------------9

3.2 Toolbar ------------------------------------------------------------------------------------------------------------------ 10

3.3 Tabs---------------------------------------------------------------------------------------------------------------------- 11

PART B: OPERATION OF THE LOGOS

Start-up of the Logos.......................................................................................................... 16

Source configuration.......................................................................................................... 17

5.1 Gain ---------------------------------------------------------------------------------------------------------------------- 17

5.2 Balance or Pan-------------------------------------------------------------------------------------------------------- 17

Microphone adjustments ................................................................................................... 18

6.1 Accessing the menu-------------------------------------------------------------------------------------------------- 18

6.2 Phantom power ------------------------------------------------------------------------------------------------------- 18

6.3 HighPass filter --------------------------------------------------------------------------------------------------------- 18

6.4 Insert bypass ---------------------------------------------------------------------------------------------------------- 19

6.5 Compressor / Limiter------------------------------------------------------------------------------------------------- 19

6.6 Ducker------------------------------------------------------------------------------------------------------------------- 19

6.7 MonitorSel -------------------------------------------------------------------------------------------------------------- 20

Appendix 1: LOGOS Specifications ........................................................................................ 21

Appendix 2: Description sub-D25 and sub-D9 pinning ....................................................... 22

Appendix 3: UMC Hybrid connection (older version) .......................................................... 23

Appendix 4: UMC Hybrid connection (new version) ............................................................ 24

Appendix 5: RS-232 cable Logos............................................................................................. 25

Appendix 6: Block Diagram ...................................................................................................... 26

Index .............................................................................................................................................. 27

interstage

Phistersvej 31, 2900 Hellerup, Danmark

Telefon 3946 0000, fax 3946 0040

www.interstage.dk

pro audio with a smile

Summary of Contents for Logos




























Search results

Summary of Contents for Logos

Reviews:

Related manuals for Logos

Brands by name

Popular brands

Eela Audio Logos, Manual

Search results

Summary of Contents for Logos

Reviews:

Related manuals for Logos

Brands by name

Popular brands