background image

Important Notices About Safe Burner Operation

General Precautions

Store the burner inside. Exposure to the elements can damage the burner.

Adjustment, maintenance, and troubleshooting of the mechanical parts of this unit
should be done by people with good mechanical aptitude and experience with
combustion equipment.

Order replacement parts from Eclipse Combustion only. Any customer-supplied
valves or switches should carry UL, FM, CSA, and/or CGA approval where appli-
cable.

The best safety precaution is an alert and competent operator. Thoroughly instruct
new operators so they demonstrate an adequate understanding of the equipment
and its operation. Regular retraining must be scheduled to maintain a high degree
of proficiency. Eclipse Combustion or your local Eclipse representative can provide
training upon request.

The operator must have easy access to this Information Guide at all times.

1.0 Applications

Eclipse 100 Series Immerso-Pak burners are packaged nozzle-mixing burners de-
signed to fire long single- or multi-pass immersion tubes. Applications include large
industrial immersion heating equipment such as cleaning tanks, spray washers,
salt baths, quenching and tempering tanks, and large asphalt tanks.

WARNING

The burners covered in this Guide are designed to mix fuel with air and burn
the resulting mixture.

 All fuel burning devices can cause explosions and

fires when improperly applied, installed, adjusted, controlled, or main-
tained.

 This Guide will provide information for using these burners for their

limited design purpose. Do not deviate from any instructions or application
limits in this Guide without written advice from the Eclipse Combustion Divi-
sion in Rockford, Illinois. Read this entire Guide before attempting to light
burners. If you do not understand any part of the information in this Guide,
contact your local Eclipse representative or Eclipse Combustion before pro-
ceeding further.

100 IP burner shown

with standard valve train

ECLIPSE INFORMATION GUIDE

IMMERSO–PAK PACKAGED BURNERS

Series 100 IP

Info 355

8/96

ECLIPSE COMBUSTION

Содержание Immerso-Pak 100 IP Series










Отзывы: