EBARA DML Instruction Manual Download

Page: 1 / 18

CF006U-H002 REV.0

- 1 -

EBARA

Corporation

EBARA
Submersible Pumps

Model DML

(sewage pump)

Model DMLV

(vortex pump)

Instruction Manual

Request

Welcome to the EBARA submersible pump. EBARA fabricated the pump with special care for assuring

safe handling. Since, however, mal-operation of the pump may induce accident, correct use of the pump
referring to the instruction manual is requested.

The Instruction Manual shall be stored at a place allowing ready reference.

To the personnel of installation works

The Instruction Manual shall be handed to the user who conducts operation, maintenance, and

inspection of the pump.

Contents

(page)

１

Warning indication ....................................... 2

７

Maintenance .............................................. 12

２

Precautions of safety ................................... 3

1. Daily inspection ................................... 12

３

Introduction .................................................. 5

2. Regular inspection ............................... 12

1. Confirmation of pump and accessories 5

3. Precautions during stop-operation ...... 13

2. Confirmation of nameplate ..................... 5

4. When motor protection activated ..... 13

４

Product specification .................................... 6

Consumables ...................................... 13

５

Installation .................................................. 7

８

Troubleshooting ........................................ 14

1. Confirmation before installation ............. 7

９

Construction

...................................................

2. Installation .............................................. 7

1. Sectional view

...........................................

3. Electric wiring ......................................... 9

2. Accessory

..................................................

Disassembling and Assembling ................ 17

６

Operation ...................................................11

Limited Warranty ....................................... 17

1. Before starting ......................................11

Repair and after-sale service .................... 18

2. Test operation ......................................11

3. Operation .............................................11

This operational instruction manual
shall be handed to the user.

Summary of Contents for DML



















Search results

Summary of Contents for DML

Reviews:

Related manuals for DML

Brands by name

Popular brands

EBARA DML, Instruction Manual

Search results

Summary of Contents for DML

Reviews:

Related manuals for DML

Brands by name

Popular brands