USER MANUAL
Before Using Your SKYFUZE LED Balloon Light Please Read All Instructions:
WARNING: When using portable luminaires outdoors, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and personal injury, including
the following:
a)
Use only 120V NEMA 5-15 three-wire outdoor extension cords that have three-
prong grounding plugs and grounding receptacles that accept the appliance’s plug.
b)
Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the
circuit(s) or outlet(s) to be used for the portable luminaire. Receptacles are available
having
built-in GFCI protection and are able to be used for this measure of safety.
c)
Use only with an extension cord for outdoor use, such as an extension cord of
cord type SEW, SEOW, SEOOW, SOW, SOOW, STW, STOW, STOOW, SJEW, SJEOW,
SJEOOW, SJW, SJOW, SJOOW, SJTW, SJTOW, or SJTOOW
.
SAVE THESE INSTRUCTIONS!
1.0 SAFETY INFORMATION
WARNING – Electrical Shock
• Always disconnect the Light unit from the power source when not in use and
prior to moving, failure to do so may result in electrical shock, injury or death.
• The light is rated at IP42 and can be used in damp locations when mounted on
the tripod.
• DO NOT touch the light with wet hands to avoid the risk of electrical shock.
• ONLY use 120V NEMA 5-15 three-wire outdoor extension cords that have three-
prong grounding plugs and grounding receptacles that accept the appliance’s plug.
WARNING – Weather and Environmental Conditions
• DO NOT operate in direct rain or snow.
• DO NOT operate when mounted on the tripod in winds that EXCEED 25 MPH,
for use in winds exceeding 15 MPH the tripod must be staked or weighted with
sandbags to anchor to the ground.
• Always use in a well-ventilated area.
4.0 WARRANTY INFORMATION
3-YEAR LIMITED WARRANTY
The LED Balloon Light and associated parts purchased in the United States from an
authorized dealer will be warrantied free from manufacturing and material defects for a
period of three years for leisure and non-commercial applications from the date of
purchase, subject to exclusions detailed below.
The LED Balloon Light will be warrantied free from manufacturing and material defects for
a period of one year for rental and commercial applications from the date of purchase,
subject to exclusions detailed below.
To claim warranty all products must be registered within 90 days of purchase, please retain
proof of purchase.
The product part number and serial numbers can be found on the side of the fixture,
please retain these numbers and quote when ordering parts, require assistance or claiming
warranty
During the Warranty period any authorized dealer will, free of charge repair or replace at
the manufacturers option any product or part deemed defective due to manufacturing
workmanship or material defects as supplied.
Any replacement parts will be covered for the balance of the products warranty period
WARRANTY EXCLUSIONS
• Failures other than defects due to manufacturing workmanship or material defects which
are the result of misuse and abuse are not covered by this warranty.
• Failures due to the use of parts that are not genuine approved parts will not be covered
by this warranty.
• The Balloon Diffuser is considered a consumable item and as such is not covered by this
warranty.
• Any Modifications or non-approved parts are excluded from the warranty.
• Always Set up the tripod on a flat level
surface, ensure the tripod legs are fully
extended and the screw knob on the hub
slide connecting the legs to the center tube
is tightened so the legs do not move.
• Remove the tripod from its carry bag, stand
the tripod in its upright position with the
legs downward and the light mount
receptacle at the top.
• Loosen the bottom knob on the sliding
center hub, slightly open the legs and then
slide the hub downward until the 3 legs are
fully extended, tighten the hub knob to
secure the legs in place.
• Mount the light fixture with the tripod
mount adapter fitted as per diagram,
loosen the light clamp screw at the top of
the tripod, insert the mount into the tripod
receptacle and tighten the tripod clamp
locking screw.
• To extend the tripod, loosen the two knobs
that secure the sliding sections, extend one
section at a time, once one section is at the
desired height, do not extend further than
Loosen the knob on the
sliding hub and slide
upwards ensuring the three
legs fully closed back to the
storage position, tighten the
leg hub knob the lock the
legs in position, when closing
the legs take care to avoid
pinching or injuring hands.
Place the tripod in the carry
bag for safe storage and
transportation.
Loosen and tighten the
light clamp to secure
the light into the tripod.
Loosen and tighten the
shaft extension screws to
extend and retract the
tripod.
Loosen and tighten the
sliding hub screw to
extend and retract the
tripod legs.
WARNING
Do not extend past the red lines
3.0 OPERATION
Mount the light securely using one of the mounting accessories:
C-Clamp
– Locate the C-Clamp onto
the Base of the light fixture, ensuring
the anti-turn flange is located in the
base slot, insert the bolt into the
screw thread and tighten using the
included wrench
.
RF Remote Control
- Used to switch
the light on/off, pre-set brightness
settings and continuous dimming from
10% to 100% brightness.
The C-clamp should only
be used on a pole with a
2in outside diameter,
ensure the intended
mounting location is
fixed, stable and can
support the weight of
the fixture.
Tripod Mount
– Screw the adapter into the base of
the light fixture, ensure the mount is tightly fitted,
before fitting to the tripod ensure the tripod is
securely located as described in section 1.3.
Eye Bolt
– Screw the Eye Bolt into the base of the
light fixture ensuring the Eye Bolt is fully
tightened, ensure the intended mounting
location is fixed, stable and can support the
weight of the fixture.
Light Power and Operation
- The light is powered
on/off by plugging or unplugging the light into a
standard US 120v NEMA 5-15 3 pin socket.
OFF
ON
50%
Decrease Brightness
Increase brightness
100%
Also included are a Light carry case, AAA
Batteries for RC and safety cable to anchor to an
adjacent infrastructure fitting when hanging, the
6ft Tripod is available separately.
Always use Safety Cable when hanging or mounting
the Light with C-Clamp and Eye Bolt accessories.
AAA Batteries Carry Case Safety Cable
2.0 PRODUCT DESCRIPTION
The LED Light kit consists of:
the RED limit line this could cause the
tripod to be unstable and cause damage or
injury, securely tighten the locking knob,
repeat for the second section.
• To Retract the tripod, grip the section to be
retracted, hold it firmly whilst loosening the
locking knob, keep a firm grip otherwise
the section will drop rapidly, a pinch point
may occur that could cause hand injury.
• Once the section is retracted tighten the
locking knob repeat for the second section.
• To fold and store, if the light is fitted, power
off the light fixture and unplug, remove the
light fixture and aside.
3.0 OPERATION
(Continued)
Tripod set-up and operation (Optional Accessory)
3.0 OPERATION (
Continued)
Tripod set-up and operation (Optional Accessory)
