Installation Instructions:
Attach Handle (M) to top of DU-HA, refer to instructions on last page.
Flip and slide the seats forward so you can gain access behind the seats.
Set the DU-HA (A) in the truck behind the seats. Space the DU-HA 2” from the back wall
and center left to right. Make sure lid opens all the way and that the latches work properly
and do not hit the sides of the truck. Once you have the DU-HA positioned where you want
it you have 3 options for anchoring the DU-HA into your truck. Option 1 is to use Self-
Tapping Screws, use this option if you want your DU-HA permanently attached in your
truck. Option 2 is to use Jack-Nuts, use this option if you want to be able to remove and
re-install your DU-HA in your truck. Option 3 is to use thru-bolts, use this option for a more
secure permanent installation. Once you have the DU-HA in the desired position secure the
DU-HA to the truck using one of the three anchoring options.
Anchoring Option 1:
Self-Tapping Screws
Tools Needed:
//
Tape Measure
//
Socket – 1/4”
//
Socket Wrench or Drill
Warning:
Before drilling into the truck
fl
oor make sure the area where you are going to drill
through is clear of any electrical wiring, fuel lines, tanks, and reservoirs. You will have
to look under the vehicle to make sure there are no obstructions at the hole locations.
Insert the self-tapping screws (D) through a Washer – 1/4” (H) and the pre-drilled holes in
the bottom of the DU-HA and screw through the carpet or vinyl and into the
fl
oor of the
truck using a Socket – 1/4” and Socket Wrench or Drill. DO NOT over-tighten.
Anchoring Option 2:
Jack-Nuts
Tools Needed:
//
Drill
//
Nail or Sharp Punch
//
Socket – 7/16”
//
7/16” Drill Bits
//
Hammer
//
Socket Wrench
//
Tape Measure
//
Pliers
//
Phillips Screwdriver – #3
//
Jack-Nut Friction Wrench (supplied)
Warning:
Before drilling into the truck
fl
oor make sure the area where you are going to drill
through is clear of any electrical wiring, fuel lines, tanks, and reservoirs. You will have to
look under the vehicle to make sure there are no obstructions at the hole locations.
With the DU-HA set in your desired position, mark the two holes in the bottom of the DU-HA
on the truck
fl
oor using a nail or sharp punch. You will need to poke through the carpet
and make a mark on the metal
fl
oor of the truck. Next remove the DU-HA and pull back the
carpet or vinyl
fl
ooring to expose the metal
fl
oor. Find the previously made marks and drill a
7/16” hole at each of the marks.
Prior to installing the Jack-Nut–1/4” (E), hold the Jack-Nut with a pliers, and using the
phillips screwdriver, make a hole through the rubber on the Jack-Nut by pressing and
twisting into the rubber on the head of the Jack-Nut–1/4” (E). Next insert the Bolt Hex
Head – 1/4” x 2-1/2” (F) through the hole in the Jack-Nut Friction Wrench (J) and thread
all the way into the Jack-Nut–1/4” (E). Place the Jack-Nut–1/4” (E) in the drilled hole
(may
need a hammer to tap into hole)
. Secure the Jack-Nut to the vehicle by tightening the Bolt
Hex Head – 1/4” x 2-1/2” (F) using a Socket 7/16” and Socket Wrench, press
fi
rmly on
the Jack-Nut Friction Wrench (J) and tighten Jack-Nut – 1/4” (E) until you see the rubber
on the Jack-Nut starting to get squished. Do not over tighten (max torque = 41 in/lbs).
Remove the bolt from the Jack-Nut–1/4” (E). Repeat this procedure for the other Jack-Nut.
Note:
Jack-Nut Friction Wrench is only used to install Jack-Nuts.
It does not take a lot of
torque to break a Jack-Nut so it is best to use
a 7/16” Socket and Socket Wrench. If using a
drill with a 7/16” Socket, be very careful not
to over tighten and strip out the Jack-Nut.
2009-2014 Ford F-150 Regular Cab -
Behind-the-seat Storage
Installation Instructions
DU-HA, Inc.
//
website: www.du-ha.com
//
phone: 1.866.306.DUHA (3842)
//
fax: 1.218.998.4013
//
306 Saint Andrews Street South, Fergus Falls, MN 56537
1
2
A
B
Fits DU-HA Part Number
70201
DIVIDER – 70201
1
2
3
4
B
3
Jack-Nut
B
B
4
H
D
H
D
