background image

1

1

© 2004 Directed Electronics, Inc.  

N556U   09/04

The 556U immobilizer interface module is used when installing remote start products in vehicles equipped with

an RF (Radio Frequency) based immobilizer system. This type of system uses a small chip imbedded in the igni-

tion key, called a transponder, to transmit a very low powered RF signal. This signal is picked up through an

antenna (or coil) around the ignition switch which is then sent to the immobilizer’s transceiver. Once the correct

signal is received, the immobilizer will enable the ignition and/or fuel systems. If an attempt is made to start

the vehicle and the transceiver does not receive a valid code, the ignition and sometimes the fuel systems are

disabled. The immobilizer system will then render the remote start useless. The 556U bypasses the immobilizer

system only while the remote start is in use, maintaining the factory system’s integrity.  When the remote start

system is not in use the factory immobilizer remains fully functional.

R

REED

D  ((+

+))  1

12

2  V

Vo

olltt  IIn

np

pu

utt:: Connect this wire to a fused source of constant 12V.

B

BLLU

UEE  ((--))  SSttaattu

uss  IIn

np

pu

utt:: Connect this wire to the remote start negative (-) status output.

P

PIIN

NK

K  ((+

+))  IIg

gn

niittiio

on

n  IIn

np

pu

utt::  Connect this wire to the vehicle’s true ignition output. (Refer to 

Latching Input, page 7.)

B

BLLA

ACCK

K  ((--))  CCh

haassssiiss  G

Grro

ou

un

nd

d  IIn

np

pu

utt::  Connect this wire to the vehicle’s chassis ground.

V

VIIO

OLLEETT  ((+

+))  K

Keeyysseen

nssee  IIn

np

pu

utt::  Connect this wire to the vehicle’s positive keysense output wire. (Refer to 

Key Sense

Inputs, page 7.)

G

GR

REEEEN

N  ((--))  K

Keeyysseen

nssee  IIn

np

pu

utt::  Connect this wire to the vehicle’s negative keysense output wire. (Refer to 

Key Sense

Inputs, page 7.)

B

BLLA

ACCK

K  aan

nd

d  B

BLLA

ACCK

K//R

REED

D  W

Wiirreess:: Both of these are antenna ring wires.

B

BLLA

ACCK

K//W

WH

HIITTEE:: Refer to alternate wiring diagram.

33--PPiinn  H

Haarrnneessss

66--PPiinn  H

Haarrnneessss

PPrroodduucctt  DDeessccrriippttiioonn

556U Immobilizer Interface

Summary of Contents for 556U










Reviews: