Installation and Operating Instructions
INVAUKP572 Issue 0
Panel Heaters
Dimensions
(millimetres)
Fig. 1
Fig. 2
Model
(
s
)
Watts
A
B
PH 075
750
620
108
PH 125
1250
688
108
PH 150
1500
688
108
PH 200
2000
860
108
PH 075T
750
620
108
PH 125T
1250
688
108
PH 150T
1500
688
108
PH 200T
2000
860
108
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic precautions should always
be followed to reduce the risk of fire, electrical shock, and injury
to persons, including the following:
IMPORTANT – The wall brackets supplied with the appliance must
be used.
IMPORTANT – If the heater is installed in a room containing a bath
or shower, it must be so installed that switches and other controls
cannot be touched by a person using a bath or shower.
Do not use outdoors.
Do not locate the heater immediately below a fixed socket outlet
or connection box.
Do not cover the heater. Do not place material or garments on
the heater, or obstruct the air circulation around the heater, for
instance by curtains or pushing furniture up against the heater,
as this could cause overheating and a fire risk.
NEVER cover or obstruct in any way the heat outlet slots at the top
of the heater or the air inlet slots in the base of the heater.
WARNING – THE SURFACES OF THIS HEATER CAN BE HOT.
Momentary contact with any part of the heater should not cause
injury. However, aged or infirm persons or young children should
not be left unsupervised in the vicinity of the heater unless a
suitable guard is fitted.
This appliance is not intended for use by children or other persons
without assistance or supervision if their physical, sensory or
mental capabilities prevent them from using it safely. Children
should be supervised to ensure that they do not play with the
appliance.
Note that due care and consideration must be taken when using
this heater in series with a thermal control, a program controller, a
timer or any other device that switches on the heat automatically,
since a fire risk exists when the heater is accidentally covered or
displaced.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualified person in
order to avoid a hazard.
WARNING: IN ORDER TO AVOID OVERHEATING, DO NOT
COVER THE HEATER.
Electrical
WARNING – THIS APPLIANCE MUST BE EARTHED
The electrical installation must be carried out by a competent electrician,
and be in strict accordance with the current I.E.E. regulations for Electrical
Equipment in Buildings.
The heater is fitted with a length of flexible cable type H05VV-F size 3 x
1.0mm
2
on 0.75kW - 2.0kW models and size 3 x 1.5mm2 on 3.0kW
models,
for connection to the fixed wiring of the premises through a suitable
connection box positioned adjacent to the heater.
The supply circuit to the heater must incorporate a double pole isolating
switch having a contact separation of at least 3mm.
Supplementary Earth Bonding
Should Equipotential Earth Bonding be required the earthing conductor
in the supply cord is deemed to provide the supplementary bonding
connection (see the 17
th
Edition of the I.E.E. Wiring Regulations).
General
The
Panel heater is designed for wall mounting on the wall brackets
supplied. It should only be operated when in the upright position as
shown.
All models are splash proof to IP24 standard.
PH.... T models are fitted with a 24 hour programme timer.
Before connecting the
heater check that the supply voltage is the same
as that stated on the heater.
Wall Mounting
IMPORTANT
– The wall brackets supplied with the appliance must be
used. The heater should be positioned observing the minimum clearances
stated around the heater - see
Fig. 1
.
DO NOT
locate the heater immediately below a fixed socket outlet or
connection box.
1. Remove wall mounting bracket from the back of the
heater by depressing the spring latch at the top of each
bracket - see
Fig. 2
.
2. Fix the wall bracket securely to the wall through the four
screw holes provided.
3. Present the heater to the wall bracket, and engage lower
slots in the back with bracket.
4. Raise the heater to upright position and push the heater
onto brackets to engage top latch.
Access to the controls
To open the hinged controls cover, insert the blade of a screwdriver in
the small slot on the right hand side of the cover, and gently lever the
screwdriver outwards. On the 3kW model the controls are located on the
top right hand corner, but the operations and functions are the same
as the other models. Note: After adjustment of the controls the control
cover must be closed.
255
MIN
A
150
MIN
150
MIN
150
MIN
B
430
