![background image](http://html1.mh-extra.com/html/devilbiss/qs-5001/qs-5001_service-bulletin_2488954001.webp)
SERVICE bULLETIN
SB-19-085-P
Replaces Sb-19-085-N
IMPORTANT: Read and follow all instruc-
tions and SAFETY PRECAUTIONS before
using this equipment. Retain for future
reference.
QS-5001 AIR MOTOR DRIVE
DESCRIPTION
The QS-5001 air motor covered in this
service bulletin is designed to drive paint
agitators when connected to a source of
clean, dry, air pressure. Maximum air
input 100 PSI.
QS-5001 standard duty air motor drive,
1/4 h.p., 15:1 ratio, 20 to120 RPM for pres-
sure tank agitator. Includes air adjusting
valve with necessary hose and fittings for
hookup to tank regulator. Overall height
8", width 7-3/4".
High pressure can cause serious
injury. Pressure is maintained in
a pressure tank after the system
has been shut down. Before
attempting removal of fill plug
or cover, relieve tank pressure.
Pressure Relief Procedure
1.
Turn off the main air supply to the
tank.
2.
Close air inlet valve located on tank
air manifold.
3.
bleed off air in the tank by turning
the relief valve handle counter-
clockwise. Wait until all the air has
escaped through the valve before
removing the pressure tank cover
or fill plug.
4.
Leave the air relief valve open until
you have reinstalled the cover or fill
plug.
INSTALLATION
QS-5001 Installation onto Pressure Tank
with Agitator. (Refer to Figure 1.)
1. Place support (12) over agitator bear-
ing housing in tank lid and tighten in
place. Tighten setscrew (14) in either
screw hole.
2. Set air motor drive on support (12)
so that gear box shaft (35) engages
agitator shaft. Tighten cap screw (13).
3. For single regulation proceed as fol-
lows:
a. Remove air inlet valve from regula-
tor on tank and install service tee (1)
in regulator.
b. Reinstall air inlet valve in service
tee (1).
c. Install nipple (2) in service tee (1).
Install hose assembly (3) between
nipple and air adjusting valve (4) on
air motor.
4. For double regulation proceed as fol-
lows:
a. Remove plug from main line
port of lower regulator and install
nipple(2).
b. Install hose assembly (3) between
nipple (2) and air adjusting valve (4)
on air motor.
OPERATION
Open valve to main air line; then slowly
open air adjusting valve until agitator
turns. To extend air motor life, adjust air
pressure setting to run motor at about one
revolution per second. The agitator should
be run continuously while using the tank.
PREVENTIVE MAINTENANCE
Air Motor Lubrication
Failure to properly lubricate
the air motor will result in
premature motor failure and
will void warranty.
Lubricate air motor daily by
adding 4 or 5 drops of SAE 10
weight oil into air inlet fitting.
Periodically - Remove air adjusting valve
and air strainer and flush motor with a
clean suitable solvent. Remove trapped
particles from screen in air inlet and clean
air strainer felt.
Air Motor Gear Box Lubrication
Every 2 Days - Remove oil fill plug and
check oil level. If oil level is low, add
140-weight SAE Gear Oil or a high quality
worm gear lubricant. Replace pipe plug
and tighten to 20 foot-pounds (27 N
.
m)
of torque.
Note
Gear box oil is most easily
drained just after motor opera-
tion, while oil is still warm.
Note
Do not overfill. Overfilling may
cause oil to leak out of vent cap
on top of gear box.
Approx. 1/8" Gap
(top of oil level to
bottom of fill hole)