![background image](http://html1.mh-extra.com/html/desert-spring/ds-series/ds-series_installation-and-user-manual_2486731001.webp)
• Disconnect electrical power to the furnace before starting electrical installation. Electrical shock could
result in serious injury.
• Sharp edges may cause serious injury. Use care when making openings in ducts.
• Do not drill into air conditioning coil, refrigeration line or electrical accessory.
• Follow local standards and codes.
WARNING
CAUTION
Rotary Disc Humidifier (All Models)
Installation & User Manual
• Do not install the humidifier on the furnace jacket, only on the return air duct or plenum.
• Serious water damage may result if humidifier is exposed to freezing temperatures. Do not install humidifier
in location where ambient temperatures may drop below 32° F / 0° C.
• If the heating system also has central cooling, the humidifier supply takeoff must have a damper. The damper
should be closed during the cooling season.
• Lithium grease may be used to lubricate metal-on-plastic contact points.
• Do not connect the transformer directly to multi-speed furnace blower motors or blower motors other than
110 VAC. (Disregard for plug in style transformer)
• Turn off the water supply before starting water connection and release pressure in the system by opening a
tap or flushing a toilet.
• Install the water supply valve on household water supply pressure only.
• Follow furnace manufacturer recommendations for electrical connections if provided.
• Incorrect use of any tool can cause injury to person or product. Be sure you understand how to use the
required tools to avoid any hazards.
Arrange for professional installation if required.
• To ensure that your new humidifier will provide maximum benefit, your furnace must be operating in
accordance with the manufacturer's specifications. If your furnace is operating outside of its manufacturer's
specifications, your Desert Spring warranty could be voided.
• Ensure that the hot air supply temperature does not exceed 150° F / 65° C.
• Ensure that unit is mounted level.
Electrocution and Chemical Hazard. Can cause death, blindness or electrical shock
CUSTOMER SERVICE
Toll-free: 1-888-486-4324
Email: [email protected]
IMPORTANT
Thank you for selecting the Desert Spring® Rotary Disc Humidifier. Carefully read this manual before starting
your installation. Follow the step-by-step instructions as written. A helpful installation video is available
online at www.desertspringproducts.com/desertspring/humidifiers_rotary.asp .
Register your humidifier online at http://www.desertspringproducts.com/desertspring/warrantyreg.asp
2
2
3
3
3
Electrical Connections
Water Connections
Installing the Disc Wheel
Adjusting the water level
4
4
5
5
Connecting the air supply
About humidity
Startup and shutdown
Template
5
6
6
7
Contents
6
7
11
1
8
5
2
10
3
4
9
12
2. Humidifier assembly
• Install the float valve into the slot in the side of the basin,
ensuring that the float seal is against the outside wall
of the basin. Hand tighten the float locking nut.
3
1. Selecting a location
• This humidifier is to be mounted on the COLD AIR RETURN
(preferably on the narrow side) of a forced air heating system.
If the humidifier must be mounted on a plenum/duct which is over
12" wide or on non-metal duct, the plenum/duct must be reinforced and/or
the humidifier must be supported by other means.
• Ensure that there is sufficient clearance for the humidifier, water
supply, and air supply ductwork. If clearance problems exist with
utilities, qualified tradespeople should be called.
• Air is supplied to the humidifier with a 3' flexible duct connected to
the air take-off (with damper) mounted on the HOT AIR
SUPPLY coming out of the furnace. (Check clearance to air conditioner coil)
• Follow the instructions on the humidifier TEMPLATE (Page 7) to locate
and cut holes for the humidifier and take-off.
• Note that the top of the round take-off opening should be a minimum of
1” higher than the rectangular humidifier opening (max. 8’). Mount the take-off
so that the damper can be easily opened and closed.
3. Hanging the basin
• Hang the basin from the mounting hanger on
the COLD AIR RETURN. See template for instructions to
mount the hanger. (Page 7)
• If the optional AutoFlush and Over-Flow kits were
purchased, refer to the manuals for installation at this point.
• Ensure humidifier is level or else the overflow may not function properly.
• Install the drain into the bottom of the
basin and finger tighten retaining nut.
Note - Teflon tape is recommended for these
connections.
After ensuring that the drain is centered,
tighen securely but Do Not over tighten.
• Next install the drain cap.
• The humidifier can be configured with either
a right or left air supply. This will depend
upon the layout of your furnace.*
• Snap the motor plate and inlet into the basin.
Ensure that the basin tabs on these parts fit
into the corresponding slots in the basin. To
remove the motor plate and inlet, squeeze the
lower tab with pliers and pull upwards.
Air
Inl
et a
nd Mo
tor Plate are Intercha
ngea
ble
*
motor
plate
air inlet
basin tab
slot
drain
cap
*interchangeable: install air inlet on the side closest
to the hot air supply take-off.
retaining nut
basin
float
drain
washer
lid tab
overflow hole
(knock-out)
furnace
(humidifier
shown with
inlet removed
for clarity)
basin
hanger mounts
on inside
of the cold
air plenum
typical
humidistat
location
4. Electrical connections
• Before making electrical connections ENSURE THAT THE POWER IS OFF!
• Connect motor, transformer and humidistat as shown in diagram below.
Used supplied marettes (wire nuts) to secure the connections
5. Water connections
• The humidifier can be connected to either hard or softened water. Note: Softened water will
require more frequent cleaning, therefore the optional AutoFlush unit is recommended.
• Before starting TURN OFF THE WATER SUPPLY and relieve the pressure.
• Install the saddle valve on a copper water line as close to the humidifier as possible.
Note: For PVC piping, use appropriately sized PVC saddle (not supplied)
• CAUTION: ensure that the piercing pin is backed up into the valve body. If installing on
galvanized pipe, pre drill a 1/8" diameter for the piercing pin.
• Assemble one side of the top clamp to the bottom clamp and place over the water line
ensuring that the rubber gasket is in place over the piercing pin.
• Assemble the other side of the top clamp to the bottom clamp with remaining fastener
and tighten evenly until unit is firmly attached to water pipe.
• Connect supplied plastic water line to valve using the compression sleeve/ insert as shown below.
• Insert the waterline through the plastic compression nut and locking sleeves inside the nut
• thread the compression nut onto the float thread, and finger tighten.
• Turn the valve handle clockwise fully to pierce the water pipe. NOTE: This is the OFF/CLOSED positio
n.
Saddle valve body
Household Copper
water line
Piercing pin
Saddle valve clamp
Rubber gasket
Insert
Compression sleeve (plastic)
motor plate
v-guide Motor Plate
v-guide
tab
tab
6. Installing the disc wheel
• Hold disc wheel with open end over the duct inlet side and the closed
end over motor plate side
• Angle drive shaft into motor coupling and rotate to ensure the flange
is fully inserted into motor coupling key hole.
• Lower the opposite end of drive shaft into duct inlet V-guide.
disc wheel
7. Installing the lid and adjusting
the water level
• Fit the lid onto the basin.
• Turn on the water supply and check for any leaks.
• The float assembly should be adjusted so that the water fully
covers the discs as illustrated in 7a. This will ensure maximum
humidity output and will minimize calcium build up.
Note - look through the inlet to see the water level.
• Adjust the float by sliding up/down in slot or by adjusting
the angle of the float bulb
• Secure the float locking nut with a 9/16" wrench.
• As an additional measure, you can fit an overflow kit to the humidifier.
For more information visit www.desertspringproducts.com
8. Connecting the air supply
• Use one of the supplied gear clamps to secure the
flex ducting to the hot air take-off.
• Use the remaining gear clamp to secure the
flex duct to the humidifier's inlet.
• Make the flex duct connection as short and straight
as possible, DO NOT let the flex duct sag.
Trim excess duct.
• If the supplied flex duct is not long enough, use 6”
round rigid pipe components instead of flex duct.
• Ensure damper is set in the OPEN position.
overflow
hole*
*punch out if required
water
ensure tabs on inlet and motor plate
fit into slots in lid flanges
float
adjustment
slot
Inlet
7a
10. Startup, maintenance and shutdown
• Turn on the water supply to the humidifier turn on the electrical power and adjust the humidistat
so that the humidifier starts. Adjust humidistat to the desired setting. Regularly change the setting
in accordance with the outside temperature.
• Under normal use, scale and other minerals will accumulate in the basin. This requires periodic removal
to ensure free rotation of the disc wheel is maintained, or motor damage may result. Cleaning frequency
will depend on water quality and the amount of humidifier duty-time. For routine cleaning, remove the
drain cap to drain water and sediment from the basin, allowing the float valve to fill and rinse the basin
for a few extra seconds. If required, use vinegar, or a scale removing cleaning solution on basin and disc
wheel for major cleaning jobs.
• The optional AutoFlush accessory provides a scheduled purge/rinse cycle for the humidifier to remove
mineral accumulation and eliminate manual routine maintenance. It also assures fresh water is always
available for humidification, eliminating concerns over standing water. ALTERNATIVELY, connect a garden
hose ball valve to the humidifier drain with a length of garden hose to a floor drain.
• At season-end, or if the humidifier is not used for an extended period;
a) turn humidistat to OFF position; b) shut off water supply, and; c) slide air damper to closed position.
Remove disc wheel and drain cap to drain water from basin. Wipe sediment from basin as required with
vinegar or scale removing cleaning solution.
LET THE HUMIDIFIER DRY-OFF COMPLETELY BEFORE RE-INSTALLING DISC WHEEL.
• The disc wheel assembly is dishwasher safe in normal cycle temperatures not exceeding 150° F/65° C.
(avoid ‘heavy-duty’, or pots/pans cycles). To clean individual discs, un-tighten stainless nuts from three
alignment rods at air inlet side and remove drive shaft retaining clip. Lift end cap and remove discs from
alignment rods.
• Over time metal parts may discolor. This is a normal reaction and will not affect performance.
6
9. About humidity
• Humidity requirements will vary from home to home. Your comfort level is the best gauge of the
correct humidity. If your windows are fogged then you have too much humidity.
• In some cases it may take a week or more for the humidity to build up to the proper level. Setting
the furnace fan to run continuously will speed up this process. For related information visit the FAQ
section on our website at www.desertspringproducts.com/desertspring/faq.asp.
• Humidity buildup will be hampered by leaks through windows and doors, exhaust fans, open fireplace
dampers, and open attics.
• Some types of carpets produce static electricity even with the correct humidity.
• Tests were conducted to determine safe, relative humidity levels for homes exposed to various low
outside temperatures. Recommended humidity levels are shown in the chart below.
Disclaimer
• Except as expressly stated in this manual, Desert Spring Eco-Products Ltd makes no representation or warranty with respect to the
humidifier and disclaims all implied warranties including any warranty of merchantability or fitness for a particular purpose.
In no event will Desert Spring Eco-Products Ltd be liable to any customer or user of the humidifier for any indirect, incidental, or
consequential damages or loss of revenues or profits, whether the same are foreseeable or not, occasioned
by any cause whatsoever including, but not limited to, the installation or operation of the humidifier.
7
DESER
T SPRING
® HUMIDIFIER MOUNTING
TEMPL
ATE
TO USE
TEMPL
ATE:
-C
ut out op
ening fr
om pap
er
, r
etain inside as instr
uc
tion sheet
, outside as t
empla
te
.
-T
ap
e t
empla
te on
to RETURN duc
t/plenum so tha
t it is le
vel and dr
aw the op
ening
shap
e on
to the duc
t.
-D
rill star
ter hole in a c
or
ner
, cut out op
ening with tin snips
. U
se c
ar
e t
o cut op
ening
accur
at
ely
. C
A
UTION - CUT EDGES ARE
VER
Y SHARP
.
-H
old hanger br
ack
et against duc
t/plenum so tha
t the b
ott
om of the hanger br
ack
et is
ab
out 1/2" fr
om the t
op edge of the op
ening in the duc
t/plenum.
Ensur
e tha
t it is
le
vel and mar
k the thr
ee moun
ting b
olt lo
ca
tions
. D
rill thr
ee 3/16" holes in the
duc
t/plenum.
M
oun
t the hanger br
ack
et on the inside of the duc
t/plenum using the
3/16" machine scr
ew
s and nuts
.
Hanger ma
y b
e dr
opp
ed up t
o 3/4" t
o acc
ommo
da
te lar
ger pr
ee
xisting holes
.
HO
T AIR SUPPL
Y
TEMPL
ATE
-U
se the plastic hot air tak
e-off/damp
er assembly as a t
empla
te
.
-H
old the H
ot A
ir
Tak
e-off against the HO
T AIR supply and tr
ac
e outside the op
ening
.
-D
rill a star
ter hole inside the line and cut with c
ompass cutt
er or tin snips
.
-H
old the air tak
e-off o
ver the op
ening and mar
k the scr
ew lo
ca
tions
.
-D
rill 1/16" pilot holes and or dr
iv
e the scr
ew
s dir
ec
tly in
to the SUPPL
Y duc
t.
--M
ak
e sur
e t
o op
en the damp
er when y
ou star
t the unit.
op
en and closed
.
Pilot hole
Hanger
Installed inside
plenum/duc
t
Dr
ill holes
Hold hanger lev
el
and mar
k
hole loca
tions
1/2"
____
7
7/8
”
(200 mm)
____
6”
(150 mm)
U.S. Patents 5,795,505, 5,171,486
© 2014 Desert Spring Eco-Products Ltd, 6350 Tomken Rd. Unit 4, Mississauga, ON, Canada, L5T 1Y3
In the interest of continuous improvement the manufacturer reserves the right to change specifications without notice
4
Rev May/14
• Mount the humidistat according to the guidelines supplied in the humidistat box.
• Humidistat should be located at least 8" upstream of the Humidifier.
Parts List
Tool Suggestions
• Variety of small open end wrenches
• Level
• Slot, Philips, or #2 (red) Robertson screw driver.
• Electric drill with 1/16" and 3/16" drill bits
• Tin snips or compass cutter
• ¼” hex head screw driver
• Pencil or marker
• Tape Measure or ruler
Part #
Reference
Description
DS00004
1
Blue Basin
DS00027
2
Clear Lid
DS00013
7
Drain Assembly (Threaded insert,washer,nut)
DS00009
11
Drain Cap c/w washer
DS00015
not shown
Duct Flange (plastic damper plate)
DS00019
8
Float Assembly
DS00024
12
Manual Humidistat
DS00025
6
Humidifier Duct Air Inlet (plastic snap-in)
DS00021
not shown
Humidifier Hanging Bracket (metal J-hook)
DS00091
4
Motor
DS00030
5
Motor Mount End Plate (plastic snap-in)
DS00036
9
Self-piercing Saddle Valve Assembly
DS00046
10
Transformer 110/24VAC Plug-in
DS
-WA
3
Wheel Assembly (disc wheel,axle assembly)
DS-AX
not shown
Axel Assembly (axel, clip)
Hardware
n
ot shown
3 x 3/16” (5mm) machine nuts
4 x Marettes (wire nuts)
6 x Self
-
tapping metal screws
Water line
not shown
10’ (305cm) x 0.25” (6mm) clear plastic
Air duct
not shown
2.5’ (75cm) x 6” (15cm) flex hose
Gear Clamps
not shown
6.5” (16cm), (2x)
LV Wire
not shown
2.5’ (76cm) low voltage wire
Instructions
not shown
Manual
Parts list
Selecting a location
Assembly
Hanging the Basin
Outside Air
Recommended
Temperature Control Setting
-30
°C/-22°F
15 %
-25°C/-13°F
20 %
-20°C/-4°F
25 %
-10°C/14°F
30 %
-5°C/23°F
35 %
>0°C/32°F
40 %
ALTERNATE POWER
SOURCES (Not shown)
i)
Hard wire transformer
power from Furnace directly
ii) Direct from furnace board.
Note: Humidifier will only
operate when the furnace is
in heat mode and eliminates
fan-only operation.
For either of these options,
strictly follow the furnace
manufacturer’s instructions.
110 V
AC
manual
humidistat
motor leads
humidifier
supplied L.V.
wire
Plug-in
transformer
transformer
wires
•
If the optional Electronic Humidistat and/or Current Sensor Relay were
purchased, refer to the manuals for installation at this point.
gear clamps
Plastic duct collar
with damper
washer
float
adjustment
nut
Blue basin
wall
Float Assembly
stem
Rubber float
Seal
washer
float
adjustment
nut
Blue basin
wall
Float Assembly
stem
Rubber float
Seal
Float
Plastic water line
Basin
Push to
lock
**To release water line, push inner ring towards elbow and pull line**