Delta Childrens Products S26970-Crib Instructions For Use Manual Download

Page: 1 / 17

Style #:

Lot:

Date:

___________

4 in 1 Crib

Conforms to

ASTM F1169-10a Full

Size Crib & F1821

Safety Standards

Consumer Care:

www.DeltaChildren.com

Delta Children’s Products

114 West 26th Street

New York, NY 10001

Tele.212-645-9033

FACTORY

REV

THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.

To register your product for important safety alerts and updates to your product please

visit

www.DeltaChildren.com

and click on

Product Registration

When contacting Delta Consumer

Care you will need to reference the

above numbers. They can also be

found on the label on the Crib End

bottom rail.

Read all instructions be

fore a

ssembly and use.

KEEP INSTRUCTIONS FOR FUTURE USE

ADULT ASSEMBLY REQUIRED

Due to the presence of small parts during assembly, keep out of

reach of children until assembly is complete.

DECEMBER 16, 2011, 22729, R0

Summary of Contents for S26970-Crib


















Search results

Summary of Contents for S26970-Crib

Reviews:

Related manuals for S26970-Crib

Brands by name

Popular brands

Delta Childrens Products S26970-Crib, Instructions For Use Manual

Search results

Summary of Contents for S26970-Crib

Reviews:

Related manuals for S26970-Crib

Brands by name

Popular brands