DaytonAudio DSPB Series User Manual Download | Manualshive

Page: 1 / 47

background image

DSPB Series User Manual

Table of Contents

What types of projects can be achieved with the DSPB series? What do I need to get started?

DSPB Amplifiers Buying Guide / Examples

.................................................................................. 3

DSPB-K/KE preamp with DSP Buying Guide / Examples

............................................................. 4

Quick Start Guides

................................................................................................................................. 5

Before you start

................................................................................................................................ 5

DSPB-250 / DSPB-100 - Quick Start

.................................................................................................. 6

Combining a DSPB Amplifier with a KAB Amplifier

Quick Start

................................................... 8

How to Power the Amplifiers

....................................................................................................... 8

Sharing Audio Between the Boards

.............................................................................................. 8

Switch Control

............................................................................................................................... 9

DSPB - K / DSPB - KE - Quick Start

.................................................................................................. 10

Potentiometer Controls

.................................................................................................................. 12

DSPB-ICP1 Sigma Studio Connection - Quick Start

........................................................................ 13

DAC Assignment Table

........................................................................................................................ 15

Project examples using SigmaStudio

.................................................................................................. 16

Creating a basic SigmaStudio project for any product from the DSPB series.

.............................. 16

DAC Assignment Table

........................................................................................................................ 17

Writing to E2Prom

Burning custom SigmaStudio programs to non-volatile (non-temporary)

................................................................................................................................................... 20

2.0 Channel Sigma Studio Project.

................................................................................ 22

DSPB-100 Mono DSPB Sigma Studio Project.

.............................................................. 24

Example - DSPB-250 + KAB250v3

Active 2-Way Speaker, 4.0 System

....................................... 25

1
2
3
...
»

Summary of Contents for DSPB Series
















































Reviews:

No comments

Related manuals for DSPB Series

Brand: zapco Pages: 71

Brand: Jet City Pages: 6

Brand: OM POWER Pages: 13

FTDX1200 Series

Brand: Yaesu Pages: 20

Brand: B&K Pages: 15

Brand: Hill Audio Pages: 12

1407A POWER AMPLIFIER

Brand: Altec Lansing Pages: 17

Brand: Boss Audio Systems Pages: 8

Brand: Eden Pages: 6

Brand: Target Audio Pages: 16

Brand: BMC Pages: 20

The Prelude PC-200

Brand: Harman Kardon Pages: 6

Multi-Purpose Amplifier

Brand: VXI Pages: 1

Brand: Sonelco Pages: 2

Brand: Altronics Pages: 4

Brand: BRUEL & KJAER Pages: 54

Brand: Redback Pages: 2

Brand: Marshall Amplification Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands