background image

Product # 6380

W i r e l e s s  
Te m p e r a t u r e / H u m i d i t y  
Sta t i o n  

I n s ta l l a t i o n   M a n u a l

For Vantage Pro

®

 or Vantage Pro Plus

The Wireless Temperature/Humidity Station, referred to as the Temp/Hum 
Station in this manual, is for use with Wireless Vantage Pro

® 

weather stations.

Components

The Temp/Hum Station consists of a temperature and humidity sensor located 
in a radiation shield, plus a sensor interface module and transmitter located in 
a protective housing. 

Tools for Setup

In addition to the hardware provided, you will need some or all of the follow-
ing materials: 

• Small Phillips-head screwdriver

• Adjustable wrench or 11/32" wrench and 7/16" wrench

• Ballpoint pen or paper clip (small pointed object of some kind)

• Drill and 3/16" (5 mm) drill bit (if mounting on a flat, vertical surface)

• Four 1/4" x 1-1/2" (6 x 38 mm) lag screws (if mounting on a flat, vertical 

surface) and a wrench to fit the lag screw hex head.

1-1/2" U-Bolts

1/4" Flat Washers

1/4" Hex Nuts

3-Volt

Lithium

Battery

Mounting 

Bracket

Radiation Shield 

Assembly

Sensor Interface Module Housing

Summary of Contents for 6380 Wireless Temperature/Humidity Station













Reviews: