UNIT NO.
1
CODE
UNIT NO.
1
3. Press MODE
selector button.
4. Change the
upper digit.
1. Press
INSPECTION/TEST
button.
6. Change the
lower digit.
2. Set the
Unit No.
Normal
status
5. Press MODE
selector button.
CODE
UNIT NO.
00
27
0
00
A0
CODE
UNIT No
ON/OFF
TEMP
UP
DOWN
FAN
RESERVE CANCEL
TIMER
MODE
SWING
/ TEST
00
0
3 · 5
1
2 · 4
6
2 · 4
6
ON/OFF
button
Malfunction code
Inspection
display
Inspection/Test button
Display of indoor unit for
which a malfunction has
been detected
Operation
LED
In case of BRC1E62
1. If operation stops due to malfunction, the remote
controller's operation indicator blinks. The massage "Error:
Press Menu Button" will appear at the bottom of the
screen.
2. Press Menu/Enter button, and malfunction code will be
displayed.
* Press Menu/Enter button, and malfunction history will be
displayed in Main Menu mode.
<Wired Remote Controller>
<Wireless Remote Controller>
In case of BRC1C62
1. If operation stops due to malfunction, the remote
controller's operation LED blinks, and a malfunction code is
displayed.
2. Even if operation stops, malfunction contents are displayed
when the inspection mode is entered.
* While in check mode, hold the ON/OFF button for four
seconds or more, the malfunction history will be cleared.
(The malfunction code will blink, and the operation
mode will switch from check mode to normal mode.)
If operation stops due to a malfunction, the operation
indicating LED on the light reception section flashes.
The malfunction code can be displayed by following
the procedure.
1. Press the INSPECTION/TEST button to select
“Inspection.”
The equipment enters the inspection mode. The
“Unit” indication lights and the Unit No. display shows
a flashing “
0
” indication.
2. Set the Unit No.
Press the UP or DOWN button and change the Unit
No. display until the buzzer (*1) is generated from
the indoor unit.
*1 Number of beeps
3 short beeps :
Conduct all of the following operations.
1 short beep :
Conduct steps 3 and 4.
Continue the operation in step 4 until a buzzer
remains ON. The continuous buzzer indicates that
the malfunction code is confirmed.
Continuous beep :
No abnormality.
3. Press the MODE selector button.
The left “
0
” (upper digit) indication of the malfunction
code flashes.
4. Malfunction code upper digit diagnosis
Press the UP or DOWN button and change the
malfunction code upper digit until the malfunction
code matching buzzer (*2) is generated.
The upper digit of the code changes as shown below
when the UP and DOWN buttons are pressed.
*2 Number of beeps
Continuous beep :
Both upper and lower digits
matched. (Malfunction code confirmed.)
2 short beeps :
Upper digit matched.
1 short beep :
Lower digit matched.
5. Press the MODE selector button.
The right “
0
” (lower digit) indication of the
malfunction code flashes.
6. Malfunction code lower digit diagnosis
Press the UP or DOWN button and change the
malfunction code lower digit until the continuous
malfunction code matching buzzer (*2) is generated.
The lower digit of the code changes as shown below
when the UP and DOWN buttons are pressed.
Normal mode
Test
operation
mode
After 10 seconds
Inspection mode
Basic Screen
Malfunction
code display
Press Menu/Enter
button.
Press Cancel
button.
Malfunction history display
Press Menu/Enter
button.
Press Cancel
button.
Press Cancel button.
Malfunction code
Service contact
Model info
Main Menu
display
* Location of buttons varies by model type.
* Location of buttons
varies by the model
type.
Self-Diagnosis by Remote Controller (SkyAir,
VRV )
* While in malfunction code display mode on the
left, press ON/OFF button for four seconds or
more, the malfunction history will be cleared.
Malfunction
code display
Indoor model
code display
Outdoor model
code display
Press Inspection /
Test Operation
button once.
Press once
again.
Press once
again.
Press once
again.
Press once
again.
Select Service Contact / Model Info
button and press Menu/Enter button.
Screen
Display when
malfunction
occurs
Operation
lamp
ON/OFF
button
Cancel
button
Menu/Enter
button
