![background image](http://html1.mh-extra.com/html/cyclops/661-3/661-3_user-instructions_2704166001.webp)
--
661-3 REMOTE CAR ALARM
USER INSTRUCTIONS
Proudly designed and engineered in Australia by CYCLOPS.
Congratulations on having one of the worlds most advanced and
unique Australian designed and engineered vehicle security systems,
installed in your vehicle!
IMPORTANT NOTICE:
Ensure your installer has programmed your individual PIN code
before taking your vehicle. (see “programming new PIN” section).
BUTTON #1 (LOCk/ARM)
Arming
Press the LOCK button to arm the system, the siren will chirp twice,
the indicators will flash twice, the LED flash slowly, the doors will
lock
.
Open dOOr WArning
The siren and indicators will pulse three times if a door is detected
open while arming.
Triggering The AlArm
The alarm can be triggered three seconds after the last door is closed.
The shock sensor will become active ten seconds after the alarm is
armed.
duress lOcking
The car doors can be locked by remote control
without arming the
alarm system if the ignition switch is left in the ON position.
cAr lOcATing
While the alarm system is armed, press and hold the LOCK/ARM
button for 2 seconds to cause the siren and indicators to pulse five
times.
BUTTON #2 (UNLOCk/DISARM)
disArming
Press the UNLOCK/DISARM button to disarm the alarm system, the
siren and indicators will flash once, the LED will flash rapidly and
the doors will unlock
.
AuTO-Arming
The system will auto arm 30 seconds after the system has been
disarmed. While the ignition is on the 30 second countdown is reset.
This feature is programmable.
AuTO-lOcking
If none of the doors are detected as having been opened after
disarming, the doors will automatically lock
after 30 seconds.
diAgnOsTics
If the alarm has been triggered during an arm cycle, the siren and
indicators will flash four times when next disarmed.
Requires central locking connection - optional extra.
siren reseT
While the siren is sounding, press the UNLOCK/DISARM button
momentarily to cancel the siren sound and disarm the system fully.
unlOcking The dOOrs
Pressing the UNLOCK/DISARM button while the ignition switch is
on or off will unlock
the doors.
BUTTON #3 (PANIC /BOOT RELEASE)
pAnic
While ignition switch is Off, hold the PANIC/BOOT RELEASE
button for more than three 3 seconds to command the alarm to panic.
The siren and indicators will pulse for 30 seconds.
BOOT releAse
While the system is disarmed, momentarily press the PANIC/BOOT
RELEASE button to activate the boot release output of the alarm
system. The indicators will flash four times to confirm the action.
SILENT ARMINg
Press the LOCK/ARM and UNLOCK/DISARM button together for
two seconds to cancel the arm/disarm confirmation chirp for one
operation. The siren will still provide an OPEN DOOR WARNING
and DIAGNOSTICS in this mode.
RE-ARM & RELOCk
a. Relock: The alarm will rearm & relock
the doors in 30 seconds if
no doors have been opened. This is to prevent accidental disarm.
b. Passive arm: the alarm will automatically arm after 30 seconds if
the ignition is turned off, then the doors are closed. This feature can
be disabled.
c. Passive lock: The alarm will automatically lock the doors 30
seconds after the ignition is turned off and the last door is closed.
This feature can be enabled. Warning: Strongly recommended not to
be used as key can be accidentally locked inside the car.
d. Anti Hi-jack: When enabled, the alarm will lock the doors four
seconds after the ignition switch is turned on. The alarm will unlock
the door immediately after the ignition is switched off. This feature
will not activate while the door is open.
SPECIAL CONSIDERATIONS
If your vehicle is fitted with a fading dome light, you should only
arm the 66-3 alarm after it is extinguished as a fading dome light
will “trick” the alarm into thinking that one of the doors is open
during the arm cycle. An open door warning is signalled by 3 chirps
PROgRAMMINg NEW REMOTE
. Disarm the alarm by pressing the UNLOCK/DISARM button.
2. Open the driver’s door and leave the door open.
3. Switch ignition switch Off and On 7 times.
4. When the 7th count is reached, leave ignition switch in the ON
position.
5. Vehicle indicators will begin flashing when alarm is ready to
accept new remote codes.
6. Press the LOCK/ARM on new remote control.
7. Test remotes by arming and disarming the alarm system.
CYCL PS
VEHICLE SOLUTIONS