DO
GUIDE
DO
Check the Box
QUANTITY
PRODUCT
PART NUMBER
4
Clip, Mounting
2014237
1
Template, Overlay Cutout
4513896
1
Connector, 2-pin
2003574
4
Screw, 06-AB x 2 1/2", Pan Head, Phillips
2014276
4
Screw, 04-40 x 2", Pan Head, Phillips
2018793
* The #04-40 x 2” screws are for use with iPanel mounting kits such as the PMK-IDOC-PAD-DSW (sold separately).
Use the template that is most convenient to perform the following procedure:
1. Locate an area on the wall that is free of miscellaneous wiring and studs.
NOTE
: The iPanel requires 10 inches (254 mm) of clearance on the right side (for right-hand installation) or left side (for left-hand installation) to allow
the iPad to be removed from the iPanel.
2. Make a small hole near the middle of the designated site, and verify that the location is suitable for installation.
3. Using masking tape (or equivalent), fasten the template to the wall, verify that the template is level, and trace the opening shape on the wall.
4. Cut out the traced shape to produce the required opening.
Install the iPanel
The iPanel can be installed into a PMK-IDOC-PAD-DSW or a wall opening using the included mounting clips. Choose one of the following options.
NOTE
: Before inserting the iPanel, ensure that a cable that is capable of supplying the required power has been installed in the wall.
PMK-IDOC-PAD-DSW
Perform the following procedure to install the iPanel into a PMK-IDOC-PAD-DSW:
1. Using the supplied connector, connect the 24 Vdc cable to the POWER INPUT 24 VDC
port.
2. Install the iPanel into the PMK-IDOC-PAD-DSW. Refer to the PMK-IDOC-PAD-DSW DO
Guide (Doc. 7783) at crestron.com/manuals for details.
NOTE
: If a PMK-IDOC-PAD-DSW is to be used, the iPanel must be mounted with the opening
facing right.
Wall Opening with Mounting Clips
Perform the following procedure to place the iPanel into a mounting hole:
1. Install the four supplied 06-AB x 2-1/2” screws and mounting clips so that two are on the
top and two are on the bottom.
a. Insert the screws through the iPanel’s flange and then through the larger hole in the mounting clip.
b. Thread the screws through the smaller hole in the mounting clips and tighten the screws only enough so that the mounting clips are brought
flush with the rear of the iPanel’s flange. Do not compress the mounting clips at this time.
2. Using the supplied connector, connect the 24 Vdc cable to the POWER INPUT 24 VDC port, and position the iPanel in the mounting hole.
3. Tighten the mounting screws evenly and only enough to compress the mounting clips and secure the iPanel squarely in the mounting surface. Do
not over-tighten the screws.
IDOC-PAD-DSWC/IDOC-PAD2-DSWC
iPanel
®
In-Wall Docking Station
The Crestron
®
IDOC-PAD-DSWC and IDOC-PAD2-DSWC iPanel
®
In-Wall Docking Stations are installed in the same manner and feature similar
operation. For simplicity within this guide, the term “iPanel” is used except where noted. Similarly, “iPad” is used to denote iPad
®
, iPad 2, and the third
generation iPad. The iPad is sold separately.
For the first generation iPad, use model IDOC-PAD-DSWC. For the iPad 2 or third generation iPad, use model IDOC-PAD2-DSWC. To convert the
IDOC-PAD-DSWC to an IDOC-PAD2-DSWC, use the IDOC-PAD-DSW_CONVERSION_KIT (sold separately). Refer to the
IDOC-PAD-DSW_CONVERSION_KIT DO Guide (Doc. 7777) at www.crestron.com/manuals for details.
DO
Select a Mounting Option
The iPanel installs into a wall or lectern. It can be installed prior to hanging the drywall (pre-construction) or it can be installed after the drywall is hung
(post-construction).
For post-construction installation, the iPanel is supplied with four mounting screws and mounting clips. It can be installed for right-handed use (right-
hand installation) or left-handed use (left-hand installation). The included faceplate is for right-hand installation. For left-hand installation, use the
IDOC-PAD-DSW-FPLFT (sold separately).
For pre-construction installation, use the PMK-IDOC-PAD-DSW Pre-Construction Wall Mount Kit (sold separately). It can be used for right-hand
installation only.
If using the PMK-IDOC-PAD-DSW but an iPanel is not available, leave the hole in the mounting surface open (if permitted by local building codes) or
attach the cover plate supplied with the PMK-IDOC-PAD-DSW.
DO
Install the Device
For pre-construction installation, mount the unit to the PMK-IDOC-PAD-DSW using the included #04-40 x 2” Pan Head screws and install the included
faceplate.
For post-construction installation, mount the unit into the wall and install the included faceplate. The only tools required are masking tape (or equivalent),
a level, a gypsum board saw (or equivalent), and a #2 Phillips head screwdriver. The following installation procedures are for post-construction
installation.
Prepare the Installation Area
The iPanel is designed to be mounted into a wall or lectern. Two overlay cutout templates are supplied: one is in the shape of the required opening and
the other is a frame, with the inner area representing the shape of the required opening (refer to the illustrations below).
Thread screws through
the clips.
Mounting Screws
(4) 06-AB x 2-1/2”
Mounting Clips
14"
(356 mm)
2 13/16”
(71 mm)
2”
(51 mm)
1 7/8”
(48 mm)
1 3/4”
(44 mm)
1 1/4”
(31mm)
11”
(279 mm)
8 9/16”
(217 mm)
10 9/16”
(268 mm)
3/16”
(5 mm)
1 7/8"
(48 mm)
2"
(51 mm)
2 13/16"
(71 mm)
8 9/16"
(217 mm)
3/16"
(5 mm)
10 9/16"
(268 mm)
POWER INPUT:
From 24 VDC
Power Source
