Cornelius SPIRIT Installation Manual Download | Manualshive

Page: 1 / 41

background image

SPIRIT

POST-MIX DISPENSER

Installation Manual

IMPORTANT:

TO THE INSTALLER.
It is the responsibility of the
Installer to ensure that the water
supply to the dispensing
equipment is provided with
protection against backflow by an
air gap as defined in ANSI/ASME
A112. 1.2-1979; or an approved
vacuum breaker or other such
method as proved effective by
test.

Water pipe connections and
fixtures directly connected to a
potable water supply shall be
sized, installed, and maintained
according to Federal, State, and
Local laws.

PRINTED IN U.S.A

IMI CORNELIUS INC; 1983-96



Part No. 317961000
March 7, 1983
Revised: November 21, 1996
Control Code A

THIS DOCUMENT CONTAINS IMPORTANT INFORMATION
This Manual must be read and understood before installing or operating this equipment

1
2
3
...
»

Summary of Contents for SPIRIT










































Reviews:

No comments

Related manuals for SPIRIT

Brand: Labelmate Pages: 2

Multidrop Pico 8

Brand: Thermo Scientific Pages: 42

Brand: Danfoss Pages: 28

Brand: Iguassu Ice Pages: 16

T../MA-BTB series

Brand: Tahoe Pages: 24

Crathco G-Cool Series

Brand: Grindmaster Pages: 16

Brand: Grindmaster Pages: 6

Brand: COX Pages: 2

Brand: Coway Pages: 24

Brand: Edbak Pages: 22

Brand: Kimberly-Clark PROFESSIONAL Pages: 2

Brand: Bunn Pages: 22

Smartwell SW1156CS

Brand: Elkay Pages: 16

Brand: H2O Pages: 2

Brand: Tach-It Pages: 7

DSI DRAFT 2 GO S

Brand: Aalberts Pages: 4

Brand: Zass Pages: 16

Brand: WaterCare Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands