™
Warnings and considerations
WARNING!
Turn OFF electrical power before installing or servicing this
product. Improper use or installation can cause SERIOUS INJURY, DEATH
or LOSS/DAMAGE OF PROPERTY.
ATTENTION!
Coupez l’alimentation électrique avant d’installer ou de
réparer ce produit. Une mauvaise installation ou utilisation peut entraîner
des blessures graves, décès ou perte / dommages à la propriété.
WARNING!
This device must be protected by a circuit breaker (20A max).
ATTENTION!
Cet appareil doit être protégé par un disjoncteur (20A max.)
WARNING!
Ground this device in accordance with the National Electric
Code (NEC) requirements. DO NOT rely solely upon the yoke plate’s
contact with a metal wallbox for adequate grounding. Use the device’s
ground wire to make a secure connection to the safety ground of the
electrical system.
ATTENTION!
Cet appareil doit être en conformité avec le Code national de
l’électricité (NEC). Ne comptez pas uniquement au contact de la plaque
avant avec un boîtier mural métallique pour la mise à la terre adéquate.
Utilisez cet appareil à la terre de l’appareil pour établir une connexion
sécurisée au système électrique.
IMPORTANT!
This device must be installed by a licensed electrician in
accordance with all national and local electrical codes.
IMPORTANT!
If you are unsure about any part of these instructions,
consult a qualified electrician.
IMPORTANT!
Use this device only with copper or copper-clad wire. Do
not use aluminum wiring. This product has not been approved for use with
aluminum wiring.
IMPORTANT!
Using this product in a manner other than outlined in this
document voids your warranty. Further, Control4 is NOT liable for any
damage incurred with the misuse of this product. See “Troubleshooting.”
IMPORTANT!
Do NOT use a power screwdriver to install this device. If you
do, you may overtighten the screws and strip them. Also, overtightening
the screws may interfere with proper button operation.
IMPORTANT!
This is an electronic device with intricate components.
Handle and install with care!
IMPORTANT!
When used in conjunction with an Auxiliary Keypad
(C4-KA-xx), the wire connecting the Auxiliary Keypad to the Configurable
Keypad must not exceed 45 m (150 ft.) at 120V AC, and 30 m (100 ft.) at
277V AC.
Installation instructions
1
Ensure that the location and intended use meet the following criteria:
•
When replacing a traditional 3-way switch, refer to the “Two-Location”
sample wiring configurations provided in the appropriate load control
device installation guide.
•
Install in accordance with all national and local electrical codes.
•
The range and performance of the wireless control system is highly
dependent on the following: (1) distance between devices; (2) layout
of the home; (3) walls separating devices; and (4) electrical equipment
located near devices.
2
Turn off the local electrical power by either switching off the circuit breaker or
removing the fuse from the fuse box. To ensure the wires do NOT have power
running to them, use an inductive voltage detector.
Supported model
•
C4-KC120277 Wireless Configurable Keypad
Introduction
The Control4® Configurable Keypad is intended for use in a Control4 system. It
installs in a standard wallbox using typical wiring standards and communicates to
the Control4 system using a wireless connection.
Box contents
• Configurable
Keypad
•
Keycap Button Kit
• Wire
nuts
• Warranty
card
•
Configurable Keypad Installation Guide
(this document)
•
Keypad Button Installation Guide
Specifications
The specifications are described below.
Model number
C4-KC120277-xx
Power requirements
120-277V AC +/-10% 50/60 Hz
36-48V DC
This device requires a neutral AC connection.
Power consumption
120V: 350mW
277V: 540mW
36V DC: 430mW
Environmental
Operational temperature
0 to 40 ˚C (32 to 104 ˚F)
Humidity
5% to 95% non-condensing
Storage
-20 to 70 ˚C (-4 to 158 ˚F)
Miscellaneous
Control communications
Zigbee, IEEE 802.15.4, 2.4 GHz, 15-channel
spread spectrum radio
Wallbox volume
4.75 cubic inches
Weight
0.05 kg (0.12 lb.)
Shipping weight
0.08 kg (0.18 lb.)
Configurable Keypad
Installation Guide
Copyright ©2021, Wirepath Home Systems, LLC. All rights reserved. Control4 and SnapAV and
their respective logos are registered trademarks or trademarks of Wirepath Home Systems, LLC,
dba “Control4” and/or dba “SnapAV” in the United States and/or other countries. 4Store, 4Sight,
Control4 My Home, Snap AV, Araknis Networks, BakPak, Binary, Dragonfly, Episode, Luma,
Mockupancy, Nearus, NEEO, Optiview, OvrC, Pakedge, Sense, Strong, Strong Evolve, Strong Vers-
abox, SunBriteDS, SunBriteTV, Triad, Truvision, Visualint, WattBox, Wirepath, and Wirepath ONE
are also registered trademarks or trademarks of Wirepath Home Systems, LLC. Other names and
brands may be claimed as the property of their respective owners. All specifications subject to
change without notice.
200-00309-G 20210409MS
