![background image](http://html.mh-extra.com/html/conair/be71tc/be71tc_use-and-care-manual_2649544001.webp)
Figure 2
Figure 1
than the other). This plug will fit in a polarized
outlet only one way. If the plug does not fit fully
in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any
way.
CAUTION: BE SURE DIRECT SUNLIGHT DOES
NOT STRIKE MAGNIFYING SIDE OF MIRROR
WHEN LEFT UNATTENDED; REFLECTED
SUNLIGHT CAN CAUSE FIRE.
1. Your lighted makeup mirror will rotate 360°
so that you can use either the normal, flat
mirror or the 7x magnifying mirror located
on the opposite side.
2. Plug adaptor into any standard 120 volt wall
outlet. The mirror light is activated by touch.
Touch the base to control the light settings.
The first touch will turn the light on to the
low setting. A second and third touch
changes light settings to medium and high.
A fourth touch will turn off the mirror light.
3. After use, always touch the base to turn the
mirror to the OFF position and unplug.
4. The beauty and design of this mirror
complements any decor. Therefore, you may
wish to leave the mirror displayed. However,
if you choose to store the mirror, see
“STORAGE” for detailed information.
IMPORTANT SAFETY
INSTRUCTIONS
Read all instructions before using (this
furnishing).
WHEN USING ELECTRICAL APPLIANCES,
BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
DANGER -
TO REDUCE THE RISK
OF ELECTRIC SHOCK, ALWAYS UNPLUG
THIS FURNISHING FROM THE ELECTRICAL
OUTLET BEFORE CLEANING.
WARNING –
To reduce the risk of
burns, electrocution, fire, or injury to
persons:
1. Unplug from outlet before putting on or
taking off parts.
2. Close Supervision is necessary when this
furnishing is used by, or near children,
invalids, or disabled persons.
3. Use this furnishing only for its intended use
as described in these instructions. Do not
use attachments not recommended by
the manufacturer.
4. Never operate this furnishing if it has a
damaged cord or plug, if it is not working
properly, if it has been dropped or damaged,
or dropped into water. Return the furnishing
to a service centre for examination and
repair.
5. Keep the cord away from heated surfaces.
6. Never drop or inser any object into any
opening.
7. Do not use outdoors.
8. Do not operate where aerosol (spray)
products are being used or where oxygen is
being administered.
9. To Disconnect, turn all controls to the off
position, then remove plug from outlet.
10. Be sure mirror is not in a position where
it can reflect sunlight; reflected sunlight can
cause fire.
11. Do not use on a soft surface such as a bed,
where openings may be blocked.
12. Touch mirror base until light shuts off,
allow unit to cool and unplug cord before
replacing light bulbs.
13. Do not place or store appliance where it can
fall or be pulled into a tub or sink.
14. If an appliance falls into water, unplug it
immediately. Do not reach into the water.
15. Never use while sleeping.
16. Do not use a bulb greater than 20 watts.
Use on any 120 volt 60 hertz AC electric
outlet (ordinary house current). Do not use
in any other electrical outlet.
17. To protect against electrical hazards, do not
use while bathing or in the shower.
18. Unplug the appliance from outlet before
cleaning. Do not leave appliance unattended
when it is plugged in.
FOR HOUSEHOLD USE ONLY
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
To reduce the risk of electric shock, this fur-
nishing has a polarized plug (one blade is wider
TO REPLACE BULB
CAUTION: TURN OFF POWER AND UNPLUG.
ALLOW TO COOL AT LEAST 3 MINUTES BE-
FORE REPLACING BULB. REPLACE BULB ONLY
WITH BULB OF SAME WATTAGE RATING.
Contact a Conair service centre at 1-800-472-
7606 for replacement bulb information (ask for
replacement bulb [#RP-34. Bulbs are $1.50 a
piece, includes shipping and handling.])
1. Remove screws from left and right sides of
mirror. (Fig. 1)
2. Carefully lift off the removable housing from
the half that is affixed to the stand.
3. Unscrew the old bulb and replace with the
new bulb. (Fig. 2)
4. Carefully replace the removable half after
locating and aligning the screw holes to the
fixed half.
5. Insert screws into screw holes and tighten.
06CN1230 BE71TC_IB_BIL.indd 1
6/19/06 9:55:56 AM