background image

P R O F E S S I O N A L
M I C R O P H O N E
S

Y

S

T

E

M

S

U H F   P P L  W I R E L E S S   M I C RO P H O N E S

S Y S T E M   I N S T R U C T I O N

M A N U A L

As part of a continuous product improvement programme, we reserve the right to alter
specifications without prior notice.

Clockaudio Ltd - Headquarters

22 Arnside Road, Waterlooville, Hampshire PO7 7UP. UK
Tel +44 (0)23 9225 1193 • Fax +44 (0)23 9225 1201

e-mail [email protected]

Clockaudio North America Inc.

2891 du Meunier, Unit 103, Vaudreuil-Dorion, Quebec J7V 8P2. Canada
Tel: (450) 424-9797 • Fax: (450) 424-3660

e-mail: [email protected]

www.

clockaudio

.com

6. GENERAL INFORMATION

Always make all other connections before plugging the
DC power supply into an AC power outlet

Do not keep the devices in places of very high temperature
or humidity

For optimum reception and maximum operating distance aim
for open space between receiver and transmitter

For optimum performance use devices at least 50cm away
from known interference sources

For best pick up pattern grip the hand held microphone
around the middle of its body

Remove the batteries when transmitters are not likely to be
used for some time

When replacement batteries are needed always change both
for new ones at the same time

11745 Clockaudio R-M Manual  18/12/08  11:30  Page 1

Summary of Contents for CW 9000












Reviews: