GREAT BRITAIN
For consumer contact, please visit www.clasohlson.co.uk and click on customer service.
ENGLISH
INSTRUCTION MANUAL • Motion Detector • Model: EF700PIR • Article No: 32-6442
Ver. 200802
Features
Power switch with motion detector for flush or surface mount,
senses motion and turns on the light. It can be adjusted for:
The amount of light required for activation (day or night) and the
duration of activation (between 10 seconds and 4 minutes). Three
position switch allows easy customizing. Can be used with bulbs up
to 500W.
Function
Connection:
1. Turn off the power.
2. Take out the existing power switch.
3. Connect the cables according to Fig. 1. Neutral (blue cable) into
N and phase into L, and output to the light into both N
and OUT.
4. Place the motion detector into the pattress.
6. Mount the motion detector with the screws (4), if this does not
work the outer cover (3) can be removed by removing the screws
(1). Mount the motion detector in the pattress and thereafter
remount the outer cover (3).
7. Adjust the dials (6-7) for duration time (Time) and intensity of light
required for activation (Lux) with a mini-screwdriver according to
Fig. 3.
Setting the light/dark activation LUX
The control dial (7) (LUX) regulates the amount of light required
for activation. Adjustment is variable and goes from sun (the light
comes on whenever motion is detected regardless of time) to moon
(the light comes on when motion is detected, but only when the
room is dark).
Setting the activation time TIME
The setting dial (6) (TIME) regulates the duration of the light.
The adjustment is variable going from + (light is on for 4 min.
±1 min.) to – (the light is on for 10 sec. ±5 sec.)
Function settings
The switch has three different settings (ON - OFF - AUTO).
ON
The light is off and is not activated by the motion sensor.
OFF
The light is on and is not regulated by the motion sensor.
AUTO The light is regulated by the motion sensor and lights
up when motion is sensed for the duration of the set
in time and triggers activation when the light intensity is
adequate enough for activation.
NOTE: The light is on for the set time, after the last detected
movement; a new detected movement gives full
activation time etc.
Technical data
Type:
EF700PIR
Rated Voltage:
230 V AC, 50 Hz
Max. power:
500W Light bulb
Detection range:
120º up to 8 meters
Protection class:
Intended for indoor use
Light/dark activation:
Daylight to darkness
Setting the duration:
±±Variable from 10 ±5 sec.
to 4min. ±1
Approved by:
CE, Semko,
Note:
The motion detector should only be installed by a qualified
electrician according to the current norms and standards.
The motions sensors should only be used with light bulbs.
5. Loosen the outer cover with a screwdriver according to Fig. 2.
10. When the power is first turned on the lights will come on, it can
take up to 1 min. before the motion detector is fully functioning.
When the light goes off the setup is finished and it returns to Auto
mode. You can now test the motion detector by moving in front of
it to activate it. The light will be lit for the duration you have set.
(It is appropriate to set in the shortest duration time for light/dark
activation in the beginning and then set the desired duration time
for light/dark activation afterwards.)
8. Carefully replace the cover.
9. Set the switch (8) in the Auto (II) mode, and turn on the power.
fig 1.
Surface cover (1)
Outer cover (3)
Screw (2)
Screw(4)
Screwdriver
Wiring diagram (5)
fig 2.
fig 3.
Setting dial for
activation time (6)
Setting dial for light/dark
activation (7)
Function settings
(8)
fig 4.
ON OFF AUTO
