![background image](http://html1.mh-extra.com/html/chapin/sk-1154-1/sk-1154-1_quick-start-manual_2590286001.webp)
017659 (A) R0421
2. Extension wand and Nozzle Assembly
6-8136
Valve Kit
Kit de la válvula
Ensemble de soupape
6-8135
Dripless Shut-off
Cierre antigoteo
Arrêt anti-goutte
To attach nozzle directly to shut-off, unthread brass extension nut and metal rod. Assemble
valve seat (included), nozzle adapter and nozzle to the shut-off as shown in figure 2C. Note
orientation of valve seat. It will leak if assembled incorrectly.
6-6091
Hose Brown
Manguera
Castaño
Tuyau Brun
6-5943
Nozzle 1.0 GPM
Tobera
Buse
6-5797
Nozzle .5GPM
Tobera
Buse
6-6092
Hose Black
Manguera para trabajos
pesados Negro
Tuyau pour service
intense Noir
Metal
Rod
Brass Extension
Brass
Extension Nut
Metal Rod
Nozzle
Adapter
Shut-off to wand to nozzle assembly
Nozzle
Shut-off to nozzle assembly
2A
Metal Rod
Valve Seat
Nozzle Adapter Nozzle
2B
2C
The dripless shut-off comes assembled
as shown in figure 2A.
6-4629
Repair Parts Kit Gaskets and Seals (not included)
Juego de piezas de reparación, empaquetaduras y juntas (no incluido)
Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus)
Sk-1154-1
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious
eye or other injury.
For safe use of this product you must read and follow all instructions. Do not leave
a pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion.
Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants
and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than
the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer’s original
parts.
Never spray flammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat,
pressure, or gas producing chemicals. Always read and follow chemical manufacturer’s instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
WARNING
Note:
Your particular sprayer may not include all parts pictured above.
Nota:
Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque :
Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
Parts, Piezas, Pièces
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
6-5373
Holster
Funda
Étui
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.
1-800-950-4458 www.chapinmfg.com
5A
5A
Lock
Position
5B
5B
TO LOCK HANDLE:
Push handle down to depress
coil spring and turn handle 1/4 turn clockwise,
then allow handle to raise into lock position.
5. Pressurizing and Spraying
1. Hose to Tank
1A
5C
5C
TO RELEASE HANDLE:
Push down to depress
coil spring and turn
handle counterclock-
wise 1/4 turn, then lift
handle.
Pump until you feel
resistance.
TO UNLOCK PUMP: Turn
handle counterclockwise
until 3-prong clamp is
loose. Then rotate clamp
counterclockwise to
stop and lift out.
5D
5D
5E
5E
5F
5F
TO LOCK PUMP: Place pump prongs down into
slots in funnel, turn clamp clockwise to furthest
position under bottom slot, then turn handle
clockwise until tightly locked and sealed in place.
FOR HELP USING TRI-LOCK PUMP SEE VIDEO
https://chapinmfg.com/pages/industrial-videos
6. Lock Off
For safety lock-off feature (no-spraying), push
trigger forward and rotate locking mechanism
into lock-off positionas shown in fig. 6A.
7. To Release Pressure
1)
Do:
With pump facing away, turn locked handle counterclockwise until air begins to escape.
Stop turning handle when you hear air escaping.
2)
Do:
Stay away from the sprayer until all air has escaped.
8. Care, Storage and Maintenance
1)
Do:
Follow chemical manufacture’s instructions for cleaning. Rinse thoroughly with recommended solvent.
Follow Filling, Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the
wand and nozzle are thoroughly rinsed after each use.
2)
Do:
Open shut-off and allow recommended solvent to run through discharge assembly.
3)
Do:
Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4)
Do:
Store sprayer tank upside down, with pump removed, in a warm dry location.
5)
Do:
Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
6A
6A
Lock
Trigger
3. Pre-Use Check
1)
Do:
Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2)
Do:
Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are
found, replace hose before using. Replace with original manufacturer’s parts only.
3)
Do:
Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and
exterior of tank for signs of deterioration of body and bottom. Any sign of deterioration indicates
possible tank weakening and could result in explosive bursting under pressure. If any of these
signs are found, discard tank immediately and replace. Do not attempt to patch leaks, etc., as
this could result in serious injury.
4)
Do:
Follow Filling, Pressurizing and Spraying Instructions, except use water only
(Pump plunger 10-20 strokes and inspect for leaks).
5)
Do:
Direct shut-off away from you and open to make sure discharge is not clogged.
6)
Do:
If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank,
and proceed with Filling, Pressurizing and Spraying Instructions.
7)
Do:
Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting.
If any of these conditions are found, replace affected part with original manufacturer’s part
before using.
4. Filling
1)
Do:
Turn pump handle counterclockwise and remove pump
2)
Do:
Prepare spray solution following all directions and safety warnings on chemical label.
3)
Do:
Fill tank to no more than the proper gallon marker. Do NOT: over fill to accommodate pump.
4)
Do:
Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and
tighten securely.
Attach the hose by screwing the swivel
nut clockwise and tightening to 37 in. lbs.
Refer to Pre-use check before using.