background image

D

F

GB

NL

Anleitung

– Drehtorantrieb Modell HC250

Instructions

– Portail à battants modéle HC250

Instructions

– Wing gate opener model HC250

Instrukties

– Draaihekopener model HC250

Für Service:  (06838) 907-100

Pour Service:  .03.87.98.15.93

For Service: 0800 317847

Voor Service: 020 6847978

F

NL

D

GB

B

B

B

B

D e c l a r a t i o n   o f   C o n f o r m i t y

Automatic Gate Opener ...........................................................................Model No.HC250
is in conformity to the 
applicable sections of Standards ....................................................EN55014, EN61000-3,

EN60529, ETS 300 683,
EN60555, & EN60335-1
EN60034

per the provisions & all amendments
of the EU Directives .....................................................................73/23/EEC, 89/336/EEC

D e c l a r a t i o n   o f   I n c o r p o r a t i o n

Automatic Gate Opener Model HC250, when installed and maintained according to all
the Manufacturer’s instructions in combination with a Garage Door, which has also
been installed and maintained according to all the Manufacturer’s instructions, meet
the provisions of EU Directive 89/392/EEC and all amendments.

I, the undersigned, hereby declare that the equipment 

specified above and any accessory listed in the manual

conforms to the above Directives and Standards.

Chamberlain GmbH
D-66793 Saarwellingen
May, 2000

Colin B. Willmott

Chefingenieur

Summary of Contents for HC250





































Reviews: