background image

TO WATCH VIDEOS GO TO: 

tinyurl.com/lgh5x3h

 

Contents

Preparation ......................................2-5
Assembly .......................................6-10
Installation ..................................11-28
  Install the Door Control ............21-22
  Install the Protector System® ....23-26
 Power 

......................................27-28

Adjustments .................................29-31
MyQ® Smartphone Control .................32 
Operation .....................................33-37
  Using your Garage Door Opener .....34
  To Open the Door Manually ...........34
  

Multi-Function

Control Panel ...........................35-36

   Remote Control and

Keyless Entry ................................36

 Homelink® 

...................................36

  To Erase the Memory .....................37
Maintenance .....................................38
Troubleshooting ...........................39-40
Accessories ........................................41
Warranty ...........................................42
Repair Parts .................................43-44

Owner’s Manual

C450

Chain Drive 

Garage Door Opener

FOR RESIDENTIAL USE ONLY

PRE-PROGRAMMED REMOTE CONTROL 

INCLUDED

www.chamberlain.com

www.mychamberlain.com

•  Please read this manual and the enclosed safety materials carefully!
•  Fasten the manual near the garage door after installation.
•  The door WILL NOT CLOSE unless the Protector System

®

 is connected 

and properly aligned.

•  Periodic checks of the garage door opener are required to ensure 

safe operation.

•  The model number label is located on the front panel of your garage 

door opener.

• This garage door opener is compatible with MyQ® and 

S

b

2.0® accessories.

•  DO NOT install on a one-piece door if using devices or features 

providing unattended close. Unattended devices and features are 

to be used ONLY with sectional doors.

Smart Garage Opener

Summary of Contents for C450













































Reviews: