background image

CONTENTS

Preparation . . . . . . . . . . . . . . . .1-2

Assembly  . . . . . . . . . . . . . . . . . . 3

Installation  . . . . . . . . . . . . . . . 4-11

Install the Door Control . . . . . . 12-13

Install the Protector System

®

. . 14-17

Power. . . . . . . . . . . . . . . . . . 18-19

Adjustments  . . . . . . . . . . . . . 20-22

Operation  . . . . . . . . . . . . . . . . .  23

Features . . . . . . . . . . . . . . . . . .  24

Door Control  . . . . . . . . . . . . . 25-26

Remote Control  . . . . . . . . . . . . .  27

To Erase the Memory  . . . . . . . . .  27

To Open the Door Manually . . . . .  28

Maintenance . . . . . . . . . . . . . . .  29

Troubleshooting. . . . . . . . . . . 30-31

Accessories. . . . . . . . . . . . . . . .  32

Warranty. . . . . . . . . . . . . . . . . .  33

Repair Parts  . . . . . . . . . . . . . 34-35

1/2 hp
Garage Door Opener

The Chamberlain Group, Inc.

845 Larch Avenue

Elmhurst, Illinois 60126-1196

■ 

 Please read this manual and the enclosed safety materials carefully!

■ 

 Fasten the manual near the garage door after installation.

   The door WILL NOT CLOSE unless the Protector System

®

 is connected and properly 

aligned.

■ 

 Periodic checks of the garage door opener are required to ensure safe operation.

  The model number label is located on the front panel of your garage door opener.

   This garage door opener is ONLY compatible with MyQ

®

 and Security

 2.0™ 

accessories. 

   ONLY enable the Timer-to-Close or MyQ

®

 remote operation feature when the 

garage door opener is installed on a sectional door.

  NOTE:

 If you are installing the garage door opener on a one-piece door, visit 

www.liftmaster.com for installation instructions.

www.liftmaster.com

Serial Number:

Date of Purchase:

 

Models
• M885
• M8856

FOR RESIDENTIAL USE ONLY 

Write down the following information for 
future reference:

..

Summary of Contents for AccessMaster M885





































Reviews: