Children operating or playing with a garage door opener
can injure themselves or others.
The garage door could
close and cause serious injury or death.
Do not allow
children to operate the wall push button(s) or remote
control(s).
A moving garage door could injure or kill someone
under it.
Activate the opener only when you can see the
door clearly, it is free of obstructions, and is properly
adjusted.
WARNING
CAUTION
WARNING
ADVERTENCIA
WARNING
The push buttons on the 2-Channel remote controls can
activate garage door openers, entryways and/or light controls.
(Instructions for programming light products are included with
those accessories.)
In general, code switch remote controls are used when
several
persons are operating the
same
device. Code
switches must be set to matching positions in
all
remote
controls used to operate the
same receiver.
Follow the
instructions for Figures 1 and 2.
Use the "smooth" push
button, as shown in Figure 1, exclusively for code switch
application.
Model 82LM 2-Channel Remote Control
OWNER’S MANUAL
©
Program Receiver to Match Remote Control Code:
Each
receiver must be programmed to accept the code of the
remote push buton that will be used to operate the device.
When
several remotes
will operate the
same device
, it is only
necessary to use the "smooth" push button of
one remote
to
program the receiver.
Select a remote control push button to operate the receiver.
• Press and HOLD the selected push button, Figure 1.
• Then press the "SMART" button on receiver panel, Figure 3.
The green indicator light will FLASH once. Release the remote
control push button.
Now the device will operate with the selected remote push button.
NOTE: If the remote push button is not held down until the
indicator light flashes, the receiver has not accepted the
code.
• Place remote circuit boards side by side. Make sure you set
code switches 1 through 9 in all remotes to matching positions
(see Figure 2). Use a pen or a screwdriver to move the
switches to (+), (-) or (0).
• Replace the battery compartment cover.
1
23456789
+
0
1
23456789
+
0
Match
Code
Switches
(1-9)
Figure 2
Select Remote
Control Push Button
Green Test Light
Figure 1
"Smart"
Button
Green
Indicator Light
KG
KG
1
3
9
7
5
1
3
9
7
5
1
2
3
Figure 3
For service, dial our toll-free number: 1-800-528-9131
12V battery ...............................................................................10A14
Visor Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29C128
Remote case only (circuit board not included)....................41A4680
Replacement Parts
Access the code switches in the 2-Channel remote(s) as
follows:
• Slide back the battery compartment cover on the bottom of the
remote control housing.
To Erase All Remote Codes:
• Press and hold the "Smart" button on the receiver until the
indicator light turns off (about 6 seconds).
All
the codes the
receiver has learned will be erased.
• Follow code switch setting instructions and reprogram receiver
as described above.
The Remote Control Battery:
The green test light should glow and the device should operate
when the remote is activated.
The 12V battery should produce power for at least a year. If the
green test light is
dim
or
does not come on,
replace the battery.
To change the battery, slide back the battery compartment
cover. Position the new battery as indicated. Replace the
battery compartment cover.
You can attach the remote control to the visor
of your car with the clip provided, if desired.
Representative Receiver
with "SMART" Button
To comply with FCC rules, adjustment or modification of receiver and/or
transmitter is prohibited, except for changing the code setting and
replacing the battery. THERE ARE NO OTHER USER SERVICEABLE
PARTS.
Visor
Clip
© 1996, Chamberlain Group, Inc.
114A2025
All Rights Reserved
Printed in Mexico
