background image

1

CIRCUIT BREAKER

(TRIp BREAKER foR ThE

CIRCUIT yoU wIll BE

woRKIng on)

fUSE BoX

(REmovE fUSE foR ThE

CIRCUIT yoU wIll BE

woRKIng on)

  The blades in each pack are matched for equal 

weight  to  assure  smooth  fan  operation.  If 
more than one fan is being installed, be careful 
not to mix blades from different cartons.

  Inspect the contents of your carton for possible 

shipping or handling damage and report any 
such  damage  directly  to  your  authorized 
Casablanca dealer.

  It is always a good idea to have an assistant to 

help with the installation.

  When  cleaning,  painting,  or  working  near 

your fan, be very careful of the fan and blades. 
Always turn the power OFF to the ceiling fan 
before servicing it, working on it, or replacing 
light bulbs. 

  Never insert anything into the path of the fan 

blades while the fan is in operation.

•  Never install a fan over a pool or spa. 

  Never operate a fan that has been damaged in 

any way. Contact Casablanca Fan Company 
by calling toll free 1-888-227-2178, or contact 
your  local  authorized  Casablanca  dealer  for 
assistance in obtaining service.

CONTENTS

READ AND SAVE THESE INSTRUCTIONS

•  This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for 

ceiling fan installations, if it is not, a new box must be installed. Casablanca extension poles are available for 

sloped or high ceiling installations.

• 

This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The 

maximum current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. 

Maximum light current is 1 amp or 100 watts of lighting.

  Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy 

hatch, make sure all wires are within the canopy and that no wires are being pinched.

For best performance and for your warranty to be valid,

use only genuine Casablanca blades, light fixtures, and accessories.

SAFE USE

Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product 
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this 
owner’s manual completely and carefully. Retain this manual for future reference.

SAFETY FIRST

INTRODUCTION 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  1

mOUNTINg RECOmmENDATIONS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2
fAN INSTALLATION 

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3

CONTROL fEATURES:
 

REmOTE OpERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8

TROUbLESHOOTINg   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

BEFORE YOU START

PN C1043001    AT1208

CAUTIon: To avoid possible electrical shock, make certain that electricity is turned 
off at the circuit breaker or fuse box before attempting any installation procedure.

18

"

84

64

Summary of Contents for Modena II












Reviews: