background image

Instructions

   See Through Masonry Fireplace Installation Instructions

Model 

MODELS TFS43-ST and *OFS43-ST

THIS WOOD-BURNING FIREPLACE COMPLIES WITH UL127 STANDARD AS A FACTORY-BUILT 

APPLIANCE.

WARNING:

 THIS FIREPLACE IS APPROVED FOR USE AS A WOOD BURNING FIREPLACE.

IT HAS NOT BEEN TESTED OR APPROVED FOR UNVENTED GAS LOGS.

WARNING:

  IMPROPER  INSTALLATION, ADJUSTMENT, ALTERATION,  SERVICE  OR  MAINTENANCE  CAN 

CAUSE INJURY, PROPERTY DAMAGE OR LOSS OF LIFE. REFER TO THIS MANUAL FOR ASSISTANCE OR 

ADDITIONAL INFORMATION. CONSULT A QUALIFIED INSTALLER OR LOCAL DISTRIBUTOR.

SAVE THIS BOOK

 This book is valuable. In addition to instructing you on how to install and maintain your appliance, it also contains information that will enable 

you to obtain replacement parts or accessory items when needed. Keep with your other important papers.

Do not store gasoline or other flammable vapors and 

liquids in the vicinity of this or any other appliance.

REV 07 APR 2013

Report No.

08-154

ICC Evaluation Services 

Report No. 2401

*OFS MODELS SHOULD  BE CROSS REFERENCED WITH THE SUPPLEMENTAL OUTDOOR FIREPLACE INSTALLATION GUIDE WHEN

INSTALLING OUTDOOR FIREPLACES.  PLEASE REFER TO THE SUPPLEMENTAL OUTDOOR FIREPLACE INSTALLATION GUIDE FOR 

IMPORTANT INFORMATION SPECIFIC TO OUTDOOR FIREPLACE INSTALLATIONS. i

IF YOU DID NOT RECIEVE AN OUTDOOR FIREPLACE INSTALLATION GUIDE ONE MAY BE DOWNLOADED AT WWW.BURNTECH.COM

Summary of Contents for OFS43-ST

























Reviews: