background image

 

 

INSTALLATION INSTRUCTIONS 

 
 
 

AVMS-3604.doc  

Page 1 of 9 

 

2012-2014 F-150 4” MyFord factory display 

360º Vision System 

(Kit # AVMS-3604) 

 

Please read thoroughly before starting installation and check that kit contents are complete. 

 

Items Included in the Kit: 

Tools & Supplies Needed: 

Video interface for 4” MyFord display 
2004-2014 Tailgate handle w/camera 
360º camera module 
Key box power/image buttons 
Front camera w/grill mount and harness 
2 side mount cameras w/pods and harnesses 
2 video output RCA cables 
Power/camera input harness 
2 side camera templates 
Mounting screws and gaskets 
These instructions 

Wire strippers 
Wire cutters 
Electrical tape 
Zip ties 
Plastic panel removal tools 
Screwdriver 
7 mm socket  
Drill 
Large Uni-bit/drill bits 
Hole saws 

 

    Safety Precautions: 

 

Work in well ventilated area that is clear of obstructions. 

 

Secure vehicle with tire chucks in both front and rear of tires. 

 

Turn vehicle accessories OFF and ensure ignition key is in OFF position. 

 

Wear safety goggles and snug fitting clothes. 

 

Use tools only for their intended purpose and which are in good repair. 

 

Only perform this task if confidence, skill, and physical ability permit. 

 

NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color 

instructions, as well as an installation video, please visit www.brandmotion.com 

 

Section 1: 

Front camera installation 

1.

 

Front camera is mounted in the grill below 
the Ford emblem. 

2.

 

Mount camera in housing using the bracket 
and screws provided. 

 

 

3.

 

Mount the housing using the provided 
screws to the grill and putting the caps in 

the holes to close them. 

 

 

Summary of Contents for AVMS-3604










Reviews: