background image

“Battery Prog Brain” the programmable ERD unit.

This unit has the ERD feature (Engine Running Detection).
Then detecting electronic noises the BPB will be in a standby mode, it will 
not disconnect the power even when the battery energy is lower than the 
disconnecting threshold.

IMPORTANT NOTE: After installation, test the ERD function to make sure 
your vehicle electronic noises are detected, if not then you need to 
connect the “engine on” wire (see “Engine On” wire instructions)

What is the “Battery Paog Brain” (BPB)
Battery

 Prog

 Brain is an innovative accessory that easily installs to any battery. 

Using unique micro-electronic technology it continually monitors the 
battery power. When Battery 

Prog

Brain detects power falling below the 

threshold level required to start your engine, it automatically isolates the 
battery from the electrical system. This will ensure the battery always have 
enough power to start your engine and will prolong the battery life. There 
are a few ways to reset the power according to the type of BPB you have 
purchase.

*Type III & IV (Gold) have the ability to disconnect the battery from the
electrical system intentionally and to act as an anti-theft device.

*Type IV RV (Utility) is designed to extend battery life by protecting
utility/house/coach batteries rather than the vehicle starting battery and 
can disconnect the battery from the electrical system intentionally to
preserve battery power when not in use.

Summary of Contents for Battery Prog Brain











Reviews: