BN Products DBC-16H Manual Download | Manualshive

Page: 1 / 12

background image

3450 Sabin Brown Road • Wickenburg, AZ 85390

(800) 992-3833 • (928) 684-2813 • [email protected]

BN PRODUCTS-USA, LLC.

DBC-16H_TM_16

Page | 1

DBC-16H

Portable Electric #5 (16mm) Combination

Rebar Bender and Rebar Cutter

Please note:

This tool is rated for #5 (16mm) Grade 60 Rebar Only

. Do not try to bend

or cut material larger in size or rebar harder than grade 60 or you will cause tool damage

or machine failure.

1
2
3
...
»

Summary of Contents for DBC-16H













Reviews:

No comments

Related manuals for DBC-16H

Brand: Parkside Pages: 34

Brand: Zenoah Pages: 16

Brand: Garland Pages: 64

Brand: Craftsman Pages: 26

Brand: Craftsman Pages: 26

Brand: Craftsman Pages: 23

Brand: Craftsman Pages: 18

Brand: Craftsman Pages: 37

Brand: Craftsman Pages: 47

Brand: Craftsman Pages: 52

Brand: Laski Pages: 37

TRIMMER ATTACHMENT SRM-260SB

Brand: Echo Pages: 24

Brand: Ukcutter Pages: 27

PULVERISETTE 19

Brand: Fritsch Pages: 62

Brand: Maruyama Pages: 46

Brand: TASKMASTER TOOLS Pages: 16

Brand: Martin Yale Pages: 5

Brand: Martin Yale Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands